CC408 | Quick Reference Guide | 2. Installer’s Programming Commands EN | 7
Bosch Security Systems | 6/04 | 4998152468B
2.1.3 STAY Mode 2
Press and hold the [0] key until two beeps sound.
2.1.4 Arm All Areas in AWAY Mode
This function allows a code to simultaneously arm,
in AWAY Mode, all areas to which the code is
assigned. This function eliminates the need to arm
each area individually.
Enter your code followed by the [0] and [#] keys
(for example, [2 5 8 0 0 #]).
2.2 Disarming the System (Off)
2.2.1 AWAY Mode
Enter your code followed by the [#] key
(for example, [2 5 8 0 #]).
2.2.2 STAY Mode 1
1. Press and hold the [*] key until two beeps
sound (only if no alarm).
Or
2. Enter your code followed by the [#] key
(for example, [2 5 8 0 #]).
2.2.3 STAY Mode 2
1. Press and hold the 0 key until two beeps
sound (only if no alarm).
Or
2. Enter your code followed by the [#] key
(for example, [2 5 8 0 #]).
2.2.4 Disarm All Areas
This function allows a code to simultaneously
disarm, in AWAY Mode, all areas to which the
code is assigned. This function eliminates the need
to disarm each area individually.
Enter your code followed by the [0] and [#] keys
(for example, [2 5 8 0 0 #]).
2.3 Isolating Zones
2.3.1 Standard Isolating
1. Press the [*] key twice.
2. Enter the zone number to isolate followed by
the [*] key.
Repeat Step 2 if more than one zone must be
isolated.
3. Press the [#] key to exit when finished.
2.3.2 Code to Isolate
1. Press the [*] key once.
2. Enter your user code.
3. Enter the zone number to isolate followed by
the [*] key.
Repeat Step 2 if more than one zone must be
isolated.
4. Press the [#] key to exit when finished.
2.4 Set First Test Report
1. Enter the Installer Code followed by the [1]
and [#] keys (for example, [1 2 3 4 1 #]).
2. Enter the number of days (0 to 15) to wait
until the first Test Report, followed by the [#]
key.
2.5 Event Memory Recall
Enter the Installer Code followed by the [8] and
[#] keys (for example, [1 2 3 4 8 #]).
The last 40 events (non-partitioned) or
last ten events (partitioned) display in
reverse order (that is, most recent to
least recent).
2.6 Walk Test Mode
1. Enter the Installer Code or Master Code
followed by the [7] and [#] keys (for example,
[1 2 3 4 7 #]).
2. Test each zone.
3. Press the [#] key to exit.
2.7 Satellite Siren Service Mode
Enter the Installer Code followed by the [5] and
[#] keys (for example, [1 2 3 4 5 #]).
2.8 Telephone Monitor Mode (Toggle
On/Off)
1. Enter the Installer Code followed by the [6]
and [#] keys (for example, [1 2 3 4 6 #]).
2. To send a Test Report, press and hold the [9]
key until two beeps sound.
3. When complete, repeat Step 1 to toggle
Telephone Monitor Mode off.
Table 5: Telephone Monitor Mode Zone
LEDs
Zone LED Dialling Event
1 Telephone line seized
2 Dialling telephone number
3 Handshake received
4 Data being sent
5 Kiss-off received
None Released telephone line
To Next Page
Loading...
Need help?
General
