EasyManua.ls Logo

Bosch WGB256A90 - User Manual

Bosch WGB256A90
68 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Register your
new device on
MyBosch now and
get free benefits:
bosch-home.com/
welcome
Washing machine
WGB256A90
[en] User manual and installation
instructions

Table of Contents

Questions and Answers

  • I
    idunnAug 18, 2025
    What to do if my Bosch Washer shows E:30 / -80 error?
    • J
      Judy OconnorAug 18, 2025
      If the Bosch Washer displays error code E:30 / -80, it could be due to several reasons: * The drain pipe or water outlet hose might be blocked. Clean them to resolve this. * The drain pipe or water drain hose may be caught or jammed. Ensure they are not kinked or trapped. * The water outlet hose might be connected too high. Ensure it's installed at a maximum height of 1 meter. * An unapproved extension might be installed on the water drain hose. Remove any such extensions. * The drain pump could be blocked. * The pump cover might not be correctly assembled. Ensure it is correctly assembled. * The pump cap might not be fully screwed in. Ensure it's screwed in all the way with the handle in a vertical position.
  • J
    Joe WhiteAug 20, 2025
    What to do if my Bosch Washer displays error E:30 / -10?
    • D
      Denise GordonAug 21, 2025
      If your Bosch Washer displays error code E:30 / -10, it could be due to the following reasons: * Low water pressure. * A blocked filter in the water inflow. Clean the water inflow filter. * The tap being turned off. Turn on the tap.
  • D
    David HintonAug 23, 2025
    Why is my Bosch Washer not draining water?
    • R
      Robert MeltonAug 23, 2025
      If the water is not draining from your Bosch Washer, here are some possible causes and solutions: * The water outlet hose is connected too high. Install the water outlet hose at a maximum height of 1 meter. * The pump cover is not correctly assembled. Correctly assemble the pump cover. * Detergent dosage is too high. As an immediate measure, mix one tablespoon of fabric softener with 0.5 litres of water and pour the mixture into the compartment for manual dosing (not for outdoor clothing, sportswear or items stuffed with down). Also, if intelligent dosing is activated, reduce the basic dosage; or, if you dose manually, reduce the amount of detergent for the next washing cycle with the same load.
  • T
    tiffanycainAug 26, 2025
    How do I start the spin cycle on my Bosch WGB256A90 Washer?
    • P
      Paula FergusonAug 26, 2025
      To continue the spin programme on your Bosch Washer, select Schleudern or Abpumpen and press the start button.
  • W
    William GreenAug 27, 2025
    Why is my Bosch Washer not cleaning well and detergent is congealed?
    • A
      Anna MahoneyAug 27, 2025
      If you notice insufficient cleaning and detergent or care products have congealed in the dispensers of the intelligent dosing system of your Bosch Washer, it could be due to: * Using unsuitable detergent in the intelligent dosing system. Check if the detergent is suitable, then drain, clean, and refill the dispenser. * Incorrectly adjusted basic dosage. If intelligent dosing is activated, reduce the basic dosage.
  • B
    Brian HarrisAug 30, 2025
    What to do if I used too much detergent in my Bosch Washer?
    • D
      Diana SimpsonAug 30, 2025
      If the detergent dosage is too high in your Bosch Washer, here are some measures you can take: * Immediately mix one tablespoon of fabric softener with 0.5 litres of water and pour the mixture into the compartment for manual dosing (not for outdoor clothing, sportswear or items stuffed with down). * If intelligent dosing is activated, reduce the basic dosage. * If you dose manually, reduce the amount of detergent for the next washing cycle with the same load.
  • P
    Patricia ColeSep 1, 2025
    What to do if the detergent drawer on my Bosch WGB256A90 Washer won't close?
    • S
      Sharon SmithSep 1, 2025
      If the detergent drawer of your Bosch Washer has not been pushed in fully, push it in until the symbol goes out.
  • B
    Brooke DouglasSep 3, 2025
    How do I unblock the dosing pump on my Bosch WGB256A90 Washer?
    • J
      Jennifer CarlsonSep 4, 2025
      To resolve the issue where the pump for the intelligent dosing system in your Bosch Washer is blocked: 1. Switch off the appliance. 2. Clean the pump unit. 3. Switch the appliance on. 4. If the display appears again after you clean the pump unit, call customer service.
  • S
    stephenmcphersonSep 5, 2025
    What to do if my Bosch WGB256A90 displays E:10 / -00 / -10 / -20 error?
    • J
      jenniferweberSep 6, 2025
      If your Bosch Washer displays the error code E:10 / -00 / -10 / -20, the pump for the intelligent dosing system may be blocked. Here's how to address it: 1. Switch off the appliance. 2. Clean the pump unit. 3. Switch the appliance back on. 4. If the error reappears after cleaning, contact customer service.
  • A
    Anita WilliamsSep 8, 2025
    Why is my Bosch WGB256A90 Washer leaving clothes too wet after spin?
    • B
      Brian VasquezSep 8, 2025
      If the spin result from your Bosch Washer is not satisfactory and the laundry is too wet or damp, consider the following: * Redistribute the laundry in the drum. * Ensure the detergent drawer is fully pushed in until the symbol goes out. * Check if the pump for the intelligent dosing system is blocked. If so: 1. Switch off the appliance. 2. Clean the pump unit. 3. Switch the appliance on again. 4. If the display appears again, contact customer service. * The spin speed might be too high; set a lower spin speed next time. * The load might be too large; reduce the amount of laundry next time. * The selected programme might be unsuitable for the fabric type; choose a suitable programme.

Bosch WGB256A90 Specifications

General IconGeneral
BrandBosch
ModelWGB256A90
CategoryWasher
LanguageEnglish

Related product manuals