EasyManua.ls Logo

Bosch WGB256ABSN - User Manual

Bosch WGB256ABSN
68 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Register your
new device on
MyBosch now and
get free benefits:
bosch-home.com/
welcome
Washing machine
WGB256ABSN
[en] User manual and installation
instructions

Table of Contents

Questions and Answers

  • J
    joycesmithAug 17, 2025
    What to do if my Bosch Washer displays "E:30 / -10" and/or the water pressure is low?
    • M
      Mathew PowellAug 17, 2025
      If your Bosch Washer displays the error code "E:30 / -10" and/or the water pressure is low, it could be due to a blocked filter in the water inflow. Clean the water inflow filter. It may also be caused by the tap being turned off, so ensure the tap is on. Another possible cause is a kinked or jammed water inlet hose; make sure the hose is free from kinks and not jammed.
  • D
    Dr. Rebecca GrantAug 20, 2025
    What does "E:30 / -80" mean on my Bosch WGB256ABSN and how do I fix it?
    • K
      Kimberly HoffmanAug 20, 2025
      The error code "E:30 / -80" on your Bosch Washer indicates a problem with draining. This could be due to several reasons: * The drain pipe or water outlet hose may be blocked, so clean them. * The drain pipe or water drain hose may be caught or jammed; ensure they are not kinked or trapped. * The water outlet hose may be connected too high; install it at a maximum height of 1 metre. * An unapproved extension may be installed on the water drain hose; remove any unapproved extensions. * The pump cap may not be fully screwed in; ensure it is screwed in all the way, with the handle in a vertical position.
  • A
    Amy MaciasAug 22, 2025
    Why won't my Bosch WGB256ABSN start?
    • S
      swansonandreaAug 23, 2025
      If your Bosch Washer programme won't start, there are several potential causes: * The mains plug of the power cord may not be plugged in, so connect the appliance to the power supply. * The circuit breaker in the fuse box may have tripped, so check the circuit breaker. * There may have been a power cut, so check whether the lighting in your room or other appliances are working. * The door may not be closed, so ensure the door is closed properly. * The childproof lock may be activated, so deactivate it.
  • S
    Samuel LloydAug 25, 2025
    What to do if water is leaking out at the water outlet hose of my Bosch WGB256ABSN?
    • N
      Nicole JonesAug 26, 2025
      If water is leaking from the water outlet hose of your Bosch Washer, check if the water outlet hose is damaged and replace it. Also, verify that the water outlet hose is connected correctly.
  • D
    David ShortAug 27, 2025
    What to do if water is leaking out at the water inlet hose of my Bosch WGB256ABSN?
    • T
      turnerstephenAug 27, 2025
      If you notice water leaking from the water inlet hose of your Bosch Washer, connect the water supply hose correctly and tighten the screw connection.
  • G
    glenn70Aug 30, 2025
    Why is there heavy foam build-up in my Bosch WGB256ABSN Washer?
    • C
      Cody WestAug 30, 2025
      Heavy foam build-up can occur if the detergent dosage is too high. As an immediate measure, mix one tablespoon of fabric softener with 0.5 litres of water and pour the mixture into the compartment for manual dosing (not for outdoor clothing, sportswear or items stuffed with down).
  • Y
    Yvette FrederickSep 1, 2025
    Why is drum cleaning required for my Bosch WGB256ABSN?
    • J
      Jimmy NavarroSep 2, 2025
      Drum cleaning may be required for your Bosch Washer if the detergent dosage is too high. If you dose manually, reduce the amount of detergent for the next washing cycle with the same load.
  • J
    James CohenSep 4, 2025
    What does "E:10 / -00 / -10 / -20" mean on my Bosch Washer?
    • A
      alexander81Sep 4, 2025
      The error code "E:10 / -00 / -10 / -20" on your Bosch Washer indicates that the pump for the intelligent dosing system is blocked. To resolve this: 1. Switch off the appliance. 2. Clean the pump unit. 3. Switch the appliance on. 4. If the display appears again after you clean the pump unit, call customer service.
  • M
    Michael WhiteSep 6, 2025
    What does "H:32" mean on my Bosch WGB256ABSN?
    • D
      davidjenningsSep 6, 2025
      The error code "H:32" on your Bosch Washer indicates that the unbalanced load detection system has interrupted the spin cycle because the laundry is unevenly distributed. To solve this, redistribute the laundry in the drum.
  • A
    Ashley PriceSep 9, 2025
    What to do if my Bosch WGB256ABSN Washer displays "E:35 / -10"?
    • F
      Frank AriasSep 9, 2025
      If your Bosch Washer displays the error code "E:35 / -10", it indicates there is water in the base trough or that the appliance is leaking. In either case, turn off the water tap.

Bosch WGB256ABSN Specifications

General IconGeneral
CategoryWasher
BrandBosch
ModelWGB256ABSN
Capacity10 kg
Energy Efficiency ClassA
Spin Speed1600 RPM
Noise Level (Washing)48 dB
Noise Level (Spinning)72 dB
ColorWhite
Delay StartYes
Child LockYes
Dimensions (H x W x D)848 x 598 x 590 mm
ProgramsSynthetics

Related product manuals