Why with nothing plugged into the Bose L1 Model II power stand, a slight hum or buzz is heard?
If you hear a slight hum or buzz with nothing plugged into the power stand, check these: * Use an AC outlet tester to check the AC outlet for reversed or open (hot, neutral, and/or ground) contacts. * If you're using an extension cord, test the cord as well.
What to do if third-party-powered subwoofer sounds poor when connected to the Bass - Line Out connector on the Bose L1 Model II power stand?
If a third-party-powered subwoofer sounds poor when connected to the Bass - Line Out connector, consider these solutions: * Unplug any Bose bass modules connected to the power stand. * The signal from the Bass - Line Out might be too high; try reducing it with direct boxes or in-line pad devices. * Experiment with different connections, like balanced or unbalanced cabling, or a direct box. * Verify that the gain and input controls on the subwoofer are set correctly. * If your subwoofer has an adjustable crossover, set it to 180Hz.
What to do if Bose Speaker System system is plugged in, power switch is on, but power LED is off?
If your system is plugged in and the power switch is on, but the power LED is off, here are a couple of things to check: * Ensure that the AC outlet has power. Test it by plugging in a lamp or another device, or use an AC outlet tester. * Make sure the power cord plug on the power stand is fully inserted into the AC outlet.
What to do if no mid/high sounds heard from the L1® model II loudspeaker Bose L1 Model II Speaker System?
If you're not hearing mid/high sounds from your L1 model II loudspeaker, try these steps: * Make sure the L1 model II top and bottom arrays are firmly seated in their connectors. * Check the connections for any bent or broken parts. * Try cleaning the contacts on the loudspeaker top and bottom with an electronic contact spray cleaner.
What to do if my Bose Speaker System's power LED is green but there is no sound?
If the power LED on your Bose Speaker System is green but you're not hearing any sound, ensure that the volume control on your instrument is turned up. Also, check that the Trim level control is turned up on the power stand. Verify that your instrument is properly plugged into the Analog Input jack and try using a different cable to connect your instrument to the power stand. To rule out issues with your instrument, plug it into a different amplifier to confirm it's working correctly.
Why does my Bose Speaker System house circuit breaker keeps tripping?
If your house circuit breaker keeps tripping, consider these solutions: * If you have multiple power stands plugged into the same AC circuit, try turning them on at different times. * If you have more than three power stands on a single 15 amp circuit, move some of them to a different AC circuit.
What to do if Bose L1 Model II power LED is on (green), but no sound?
If the power LED is green but you're not getting any sound, try these steps: * Make sure the volume control on your instrument is turned up. * Check that the Trim level control on the power stand is also turned up. * Ensure your instrument is correctly plugged into the Analog Input jack. * Try using a different cable to connect your instrument to the power stand. * Plug your instrument into a different amplifier to verify it's working properly.
How to stop microphone feedback on Bose Speaker System?
To reduce microphone feedback with your Bose Speaker System: * Reposition the microphone so it doesn't point directly at the L1 model II top and bottom array loudspeaker. * Try using a different microphone. * Adjust the positions of the loudspeaker and/or vocalist on stage. * Increase the distance between the loudspeaker and the microphone. * If you're using a vocal effects processor, ensure it's not causing the feedback.
What to do if my Bose B1 or B2 bass module is plugged in, but no bass audio is heard?
If you're not getting any bass audio from your B1 or B2 bass module, here's what you can check: 1. Make sure you're using the 4-wire bass module cable that came with the module. 2. Confirm the cable is securely plugged into the Bass Module Out connector. 3. Try using a different 4-wire cable. 4. If possible, test with another bass module. 5. Ensure your power stand firmware is up to date.
What to do if Bose L1 Model II instrument or audio source sounds distorted?
If your instrument or audio source sounds distorted, check the following: * Ensure the Signal/Clip LED isn't constantly red. If it is, lower the trim level. * Try using a different audio source or instrument. * Test your current source or instrument with another power stand.
Information regarding products that generate electrical noise and FCC compliance.
Welcome message and overview of the owner's guide.
Details the advantages and capabilities of the L1™ model II system.
Describes the components of the L1™ model II system and optional equipment.
Details the connectors and controls on the power stand top panel.
Lists all components included in the L1™ model II system packaging.
Guidelines for optimal placement of the L1™ model II system for performance.
Instructions for unfolding and positioning the L1™ model II power stand.
Steps for connecting the loudspeaker sections to the power stand.
How to connect the L1™ model II system to a power source.
Instructions for connecting the B1 bass module to the power stand.
Steps for mounting and connecting the T1 ToneMatch™ audio engine.
How to connect an additional B1 bass module to the system.
Instructions for connecting the PackLite® amplifier to expand bass module support.
How to adjust the input Trim control for analog audio sources.
Guidance on operating the system with both T1 ToneMatch and analog inputs.
Examples of how to set up and use the system in different musical situations.
Instructions for cleaning and maintaining the L1™ model II system.
Procedures for cleaning the system enclosures and grilles.
Contact information for technical support and service.
Solutions for common problems encountered with the L1™ model II system.
Information on product warranty and how to register your system.
Information on available accessories for the L1™ model II system.
Technical specifications for the dimensions and weight of system components.
Electrical specifications including AC power rating and peak inrush current.
Details on audio connectors and their specifications.
General| Product color | Black |
|---|---|
| Bass adjustment | Yes |
| Recommended usage | Studio |
| Multi-Room Streaming (MRS) support | No |
| Speaker type | - |
| Number of drivers | 2 |
| Speaker placement | Stand-mountable |
| Audio output channels | - channels |
| RMS rated power | - W |
| USB 2.0 ports quantity | 1 |
| Connectivity technology | Wired |
| Power source type | AC |
Weight and Dimensions| Depth | 450 mm |
|---|---|
| Width | 260 mm |
| Height | 381 mm |
| Weight | 11380 g |
To Next Page
