Bose PowerShare PS602 Service Manual

7
Product Description
PS602 Rear Panel
1. INPUT 1 & 2 - Balanced 3-pin Euroblock and unbalanced RCA line-level input connectors.
2. USB - This allows you to use the PC-based PowerShare
TM
Editor Software to configure the advanced
features of the amplifier. The CONFIG DIP switch must be set to SOFTWARE to configure the amplifer
using the PowerShare Editor Software.
3. CHANNEL 1 & 2 EQ - Each dial provides loudspeaker equalization presets per channel: DS 16, DS
40, DS 100, FS3B, 402, 802, MA12EX, RMU105, and RMU108. Use the Flat setting for FS3 Systems.
When EQ is selected, the Vpeak and Vrms limiters for that loudspeaker are automatically loaded. Use
the PowerShare Editor Software to adjust any of these parameters. In Hi-Z output mode, a 50 Hz high
pass filter (HPF) is automatically added to the Hi-Z selected outputs. The loudspeaker EQ is applied
after the 50 Hz HPF.
4. CONTROLCENTER - RJ-45 input connector for Bose
®
CC-1 ControlCenter Zone Controllers or
CV41 4-to-1 Converter only. Do not use this input to connect to a network.
5. MUTE - Contact closure connection where a short across the mute connector will mute all outputs.
This is the Normally Open (NO) default state. The mute polarity can be inverted to Normally Closed
(NC), where an open across the mute connector will mute all outputs, using the PowerShare Editor
Software.
6. DIP Switches - Used to set the amplifier configuration. All switches set to the left position is the
standard configuration.
• AUTO STANDBY - If enabled (ON), the amplifier goes into standby mode after twenty minutes
without an input signal. If in standby mode and an audio signal is detected, the amplifier will
automatically wake and amplify audio within 1 second. The OFF position disables this feature.
• GLOBAL OUT - Sets the output capability to 70 Vrms or 100 Vrms, for all outputs that have their
OUTPUT DIP switch set to HI Z. In 70 Vrms mode, a 100 Vpeak limiter is automatically loaded. In
100 Vrms mode, a 141 Vpeak limiter is automatically loaded.
• CONFIG - In REAR mode, the rear panel EQ settings are all that are required to configure the
amplifier. In SOFTWARE mode, the PowerShare Editor Software configures the amplifier, and the
rear panel EQ switches are ignored. The rest of the DIP switch settings are independent of the
PowerShare Editor Software settings.
• SENSITIVITY - Select 4 dBu or 12 dBu as the amplifier sensitivity for the Euroblock line-level inputs.
The unbalanced RCA input sensitivity is -10 dBV in the 4 dBu sensitivity setting, and -2 dBV in the 12
dBu sensitivity setting.
• OUTPUT 1 - Select 70/100 V high impedence output (HI Z) or 4-8 ohm low impedence
output (LOW Z).
• OUTPUT 2 - Select 70/100 V high impedence output (HI Z) or 4-8 ohm low impedence
output (LOW Z).
7. OUTPUT 1 & 2 TRIM - Output attenuators for each output. Fully clockwise is 0 dB attenuation; fully
counter-clockwise is mute. If CC-1 Zone Controller(s) are used, then the CC-1 becomes the master
volume control(s). The position of each trim will determine the CC-1 Zone Controller range for that
output. Set each trim to 0 dB attenuation to allow each CC-1 Zone Controller to have full attenuation
range. If the CC-1 is disconnected from the amplifier, then the output trim setting becomes active.
8. OUTPUT - Two inverted 2-pin Euroblock connectors for loudspeaker connections. Each channel can
deliver up to 600 Watts regardless of load into 4 ohms, 8 ohms, 70 V RMS, or 100 V RMS. Outputs are
not bridgeable.
MUTE
AUTO STANDBY
SENSITIVITY
GLOBAL OUT
OUTPUT 1
OUTPUT 2
CONFIG
12 dBu
100V
Low Z
4 dBu
70V
Hi Z
1. FLAT
2. DS16
3. DS40
4. DS100
100-240V ~ 50/60Hz 700W MAX
PowerShare
PS602
5. FS3B
6. 402
7. 802
8. MA12EX
9. RMU105
0. RMU108
4
6
9
0
7
8
3
2
1
5
4
6
9
0
7
8
3
2
1
5
OFF
Hi Z
REAR
ON
Low Z
SOFTWARE
123 456 78

Bose PowerShare PS602 Specifications

General

Brand	Bose
Model	PowerShare PS602
Category	Amplifier
Language	English