EasyManua.ls Logo

Bostitch GF33PT - User Manual

Bostitch GF33PT
52 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
GF28WW, GF33PT &
GFN1564K, GFN1664K, GBT1850K
CORDLESS GAS NAILERS
CLAVADORAS INALÁMBRICAS A GAS
CLOUEUSES À GAZ SANS FIL
189774REVA 12/09
STANLEY FASTENING SYSTEMS L.P.
OPERATION and MAINTENANCE MANUAL
MANUAL DE OPERACIÓNY DE MANTENIMIENTO
MANUEL D’INSTRUCTIONS ET D’ENTRETIEN
BEFORE OPERATING THIS TOOL, ALL OPERATORS SHOULD STUDY THIS MANUAL TO
UNDERSTAND AND FOLLOW THE SAFETY WARNINGS AND INSTRUCTIONS. KEEP THESE
INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE. IF YOU HAVE ANY QUESTIONS,
CONTACT YOUR BOSTITCH REPRESENTATIVE OR DISTRIBUTOR.
ANTES DE OPERAR ESTA HERRAMIENTA, TODOS LOS OPERADORES DEBERÁN ESTUDIAR
ESTE MANUAL PARA PODER COMPRENDER Y SEGUIR LAS ADVERTENCIAS SOBRE
SEGURIDAD Y LAS INSTRUCCIONES. MANTENGA ESTAS INSTRUCCIONES CON LA
HERRAMIENTA PARA FUTURA REFERENCIA, SI TIENE ALGUNA DUDA, COMUNÍQUESE CON
SU REPRESENTANTE DE BOSTITCH O CON SU DISTRIBUIDOR.
LIRE ATTENTIVEMENT LE PRÉSENT MANUEL AVANT D’UTILISER L’APPAREIL. PRÉTER UNE
ATTENTION TOUTE PARTICULIÈRE AUX CONSIGNES DE SÉCURITÉ ET AUX
AVERTISSEMENTS. GARDER CE MANUEL AVEC L’OUTIL POUR FUTUR RÉFÉRENCE. SI
VOUS AVEZ DES QUESTIONS, CONTACTEZ VOTRE REPRÉSENTANT OU VOTRE
CONCESSIONNAIRE BOSTITCH.

Table of Contents

Other manuals for Bostitch GF33PT

Preview: Safety & Operating Instructions
Safety & Operating Instructions240 pages

Questions and Answers

  • F
    foxjamesAug 12, 2025
    Why is my Bostitch GF33PT skipping nails?
    • J
      Johnny CarterAug 13, 2025
      If your Bostitch Nail Gun is skipping nails or has an intermittent feed, ensure you are using only recommended nails. Try cleaning and lubricating the tool. If the ribbon spring is weakened or damaged, replace it. Also, a worn or damaged pusher should be replaced. Make sure to pull the trigger all the way. If the temperature is too low, warm up the fuel cell under 120°F (50°C). Other solutions may include replacing the piston ring, piston, or cylinder piston ring. For further assistance, contact Bostitch for a replacement.
  • T
    Tonya BennettAug 16, 2025
    What to do if my Bostitch Nail Gun doesn't drive nails but the green light is on?
    • C
      Christopher RobinsonAug 16, 2025
      If the fan is working and the light indicator shows green on your Bostitch Nail Gun, but it's not driving nails or the operation is unstable, ensure you push the contact arm all the way. If the temperature is too low, warm up the fuel cell to under 120°F (50°C). Check the fuel cell and exchange it with a new one if it's insufficient. Inspect the filter and clean it as instructed on the maintenance sheet. For spark plug wire, spark plug issues, contact Bostitch for replacement.
  • L
    leecourtneyAug 20, 2025
    How to fix nail jams and bent nails in my Bostitch GF33PT Nail Gun?
    • J
      Justin Murray Jr.Aug 20, 2025
      If your Bostitch Nail Gun is experiencing nail jams and bent nails, make sure you are using only recommended nails. If the pusher is worn or damaged, replace it. For a worn driver blade, contact Bostitch for replacement.
  • M
    Meredith LeeAug 25, 2025
    What to do if my Bostitch Nail Gun operates but doesn't drive nails?
    • A
      Alyssa BullockAug 25, 2025
      If your Bostitch Nail Gun operates but doesn't drive any nails, start by clearing any jams. Then, clean and lubricate the nailer. If the ribbon spring is weakened or damaged, replace it. Ensure you are using only recommended nails. You can also try pushing the driver blade with a slotted-head screwdriver and putting the piston back to the highest position.
  • G
    Gina BuckAug 28, 2025
    Why doesn't the fan operate when I press the lever on my Bostitch Nail Gun?
    • S
      Samuel ToddAug 28, 2025
      If the fan on your Bostitch Nail Gun does not operate when the push lever is pressed, first check if the magazine is empty and load more nails if needed. If the light indicator is red, charge the battery. If the light is green, contact Bostitch for replacement.
  • K
    Kimberly Davis MDAug 31, 2025
    What to do if nails are jammed in firing head of Bostitch Power Tool?
    • A
      Angela WalkerAug 31, 2025
      If nails are jammed, remove them and adjust the nailing. First, remove the fuel cell and the battery from the nailer. Then, lock the follower back in the magazine and remove the fasteners.
  • A
    Anthony MorenoSep 4, 2025
    How to fix Bostitch Power Tool driving nails too deep or shallow?
    • C
      Christian MillerSep 4, 2025
      To adjust the nail depth, follow these steps: First, remove the fuel cell and the battery from the tool. If the nails are driven too deeply, move the contact arm forward. If the nails are driven too shallow, move the contact arm backward.
  • A
    Aaron ReyesSep 7, 2025
    What to do if I experience an excessive build up of debris within the Bostitch Power Tool between cleans?
    • J
      Jonathan DavisSep 8, 2025
      If you experience an excessive build-up of debris within the tool between cleans, reduce the maintenance intervals.

Summary

Tool Illustration

Finish Tools Diagram

Illustrates components of Bostitch finish nailer models.

Framing Tools Diagram

Illustrates components of Bostitch framing nailer models.

Tool & Charger Specifications

Framing Tools Specifications

Technical data for GF28WW and GF33PT framing nailers and their chargers.

Finish Tools Specifications

Technical data for GFN1564K, GFN1664K, GBT1850K finish nailers and their chargers.

Introduction

Product Overview

General description of Bostitch Cordless Gas Nailers and manual usage guidance.

Limited Warranty

Warranty Terms and Conditions

Details Bostitch's limited warranty for cordless gas nailers in the US and Canada.

Safety Instructions

Tool and Fuel Warnings

Critical safety warnings for tool operation, fuel cells, and potential hazards.

Loading and Maintenance Safety

Safety precautions for loading the tool and performing maintenance.

Employer and Owner Responsibilities

Outlines employer/owner duties for tool safety and maintenance.

Tool Safety Warnings

Battery and Charger Safety

Essential safety guidelines for using Bostitch batteries and chargers.

Battery Charger Maintenance

Guidelines for cleaning and maintaining the battery charger.

Battery Charger Safety

Charger Operation Precautions

Safety precautions for operating the charger, especially with a DC 12V source.

Tool Battery

Battery Charger Usage

Instructions for using the battery charger and charging batteries.

Optimizing Battery Performance

Tips for maximizing battery lifespan and operational efficiency.

Loading Battery into Tool

Step-by-step guide for inserting and removing the battery from the tool.

Preparing the Fuel Cell

Attaching the Metering Valve

Instructions for attaching the metering valve to a fuel cell assembly.

Installing Fuel Cells

Fuel Cell Installation Steps

Detailed steps for properly inserting the fuel cell into the nailer.

Tool Operation Safety

Before Handling or Operating

Key safety checks and warnings before handling or operating the tool.

Cold Weather Care

Guidelines for using the tool in cold weather conditions.

Tool Safety Test

Procedure for testing the tool's safety features before use.

Loading Fasteners

Loading Finish Nailers

Instructions for loading fasteners into GF28WW, GF33PT, GFN1564K, GFN1664K models.

Unloading Finish Nailers

Instructions for unloading fasteners from GF28WW, GF33PT, GFN1564K, GFN1664K models.

Loading Framing Nailer

Instructions for loading fasteners into GBT1850K model.

Unloading Framing Nailer

Instructions for unloading fasteners from GBT1850K model.

Tool Operation

Sequential Trip Operation

Explanation of how to operate the tool using the sequential trigger system.

Jam Clearing Procedure

Steps to safely clear jammed fasteners from the tool.

Dial-a-Depth Fastener Control Adjustment

Adjusting Finish Nailer Depth

How to adjust fastener depth for GFN1564K, GFN1664K, GBT1850K models.

Adjusting Framing Nailer Depth

How to adjust fastener depth for GF28WW and GF33PT models.

Additional Safe Operation Guidelines

General safety guidelines for tool operation.

Installing the Belt Hook

Belt Hook Installation Steps

Steps to install or switch the belt hook on the tool.

Using the Non-Marring Finish Tips

Non-Marring Tip Installation

Instructions for installing non-marring tips to prevent surface scratches.

Standard Accessories

Included Accessories

List and description of standard accessories provided with the tool.

Optional Accessories

Available Optional Accessories

List of optional accessories available for separate purchase.

Bostitch GF33PT Specifications

General IconGeneral
Operating Pressure70-120 PSI
Magazine Capacity100 nails
Power SourcePneumatic
Tool-Free Depth AdjustmentYes
Tool-Free Jam ReleaseYes
No-Mar TipYes
Nail Diameter0.113 - 0.131 in
Firing ModeContact or Sequential

Related product manuals