Brady BBP31 User Manual (English)

Other manuals for Brady BBP31

User Manual168 pages

Tutorial17 pages

Questions and Answers:

J
Jennifer GoodwinSep 9, 2025
What to do if my Brady BBP31 displays 'Error reading media memory cell. Reload or replace media. If error persists, contact technical support. Errors: 48, 49, 50, 51, 52'?
- K
  Kimberly OliverSep 9, 2025
  If your Brady Label Maker displays the error 'Error reading media memory cell. Reload or replace media. If error persists, contact technical support. Errors: 48, 49, 50, 51, 52', it means the printer cannot read the media memory cell because the code is incorrect, the cell cannot be read, the data in the cell is corrupted, the cell is the wrong version or the media counter shows no media remaining. You should replace the media.
S
Shawn RiosAug 23, 2025
Why is the print faint on my Brady Label Maker labels?
- C
  Christopher StoneAug 23, 2025
  If the print on your Brady Label Maker labels is faint, it could be due to the ribbon not advancing correctly or the print energy being too low. To fix this: * Tension the ribbon by rotating the rewind spool (top spool) downward until all slack is removed. * Try another ribbon cartridge. If the issue persists, adjust the print-energy setting.
D
dustin34Aug 25, 2025
What to do if my Brady Label Maker screen freezes?
- A
  adamcolonAug 25, 2025
  If your Brady Label Maker's screen freezes, it's likely a user interface error. Here’s how to reset it: 1. Press the Power button to turn the printer off. 2. Press the Power button again to turn the printer back on. 3. If the printer doesn't shut down, press and hold the Power button for more than 5 seconds to reset the machine. 4. Release the Power button after the printer resets.
C
Christian DuncanAug 26, 2025
Why is my Brady BBP31 printing no label?
- X
  xjordanAug 26, 2025
  If your Brady Label Maker is not printing anything on the label, the label or ribbon might not be loaded correctly, or the ribbon has run out. Try reinstalling the ribbon cartridge or loading a new ribbon.
C
Courtney EstesAug 27, 2025
Why is my Brady Label Maker printing with poor quality?
- K
  Kenneth CummingsAug 28, 2025
  If your Brady Label Maker is producing poor print quality, it could be due to several reasons: * The ribbon and label media are incompatible, or you're using an incorrect label material and ribbon combination. Verify you have the correct ribbon for the label roll. * Dust or adhesives have accumulated on the printhead. * The media wiper is dirty. Clean the printhead or replace the media wiper.
B
bwhitneyAug 29, 2025
Why do void areas or lines appear on printed text from my Brady BBP31 Label Maker?
- M
  Miss Bethany HernandezAug 29, 2025
  If you see void areas or lines appearing on the printed text from your Brady Label Maker, it's likely due to ribbon wrinkling. To fix this: * Tension the ribbon by rotating the rewind spool (top spool) downward until all slack is removed. * Try using another ribbon cartridge.
J
Jade BurgessSep 14, 2025
What to do if my Brady BBP31 Label Maker displays 'Printer Error Error: 85'?
- R
  Rhonda JenkinsSep 14, 2025
  If your Brady Label Maker displays 'Printer Error Error: 85', the printer has advanced die-cut media but cannot detect the notch. This could be due to a dirty or failing sensor. Check and clear the media path, then reload the media.
D
David BarrettSep 12, 2025
What to do if my Brady Label Maker says 'Printer too warm. Print job was canceled. Error: 18'?
- A
  Alexandra BishopSep 12, 2025
  If your Brady Label Maker displays 'Printer too warm. Print job was canceled. Error: 18', it means the printhead has reached its maximum operating temperature. Allow the printhead to cool down for about 10 minutes before restarting the print job.
D
Denise HuffmanSep 7, 2025
What to do if my Brady BBP31 displays 'Printer Error. Media Jam. Print job canceled. Errors: 45, 54'?
- T
  Tonya RichmondSep 7, 2025
  If your Brady Label Maker shows 'Printer Error. Media Jam. Print job canceled. Errors: 45, 54', it means either the media is in the media guides but not detected by the leading edge sensor, or the media is detected by the sensor but not in the media guides, or the media is simply jammed. Reinstall the media and restart the print job to fix this.
J
Jared HowardSep 4, 2025
What to do if my Brady Label Maker says 'Media out. Replace media and close inside printer cover. Error: 53'?
- E
  Eric StevensSep 4, 2025
  If your Brady Label Maker displays the error 'Media out. Replace media and close inside printer cover. Error: 53', it means the tape ran out during the print job. This message might also appear if the media guides move out of the correct position during printing. To resolve this, reinstall the media and restart the print job.

Brady BBP31 Specifications

General

Print Resolution	300 dpi
Display	Color touchscreen
Cutter	Automatic
Power Source	AC power
Print Technology	Thermal transfer
Max Label Width	4 inches
Connectivity	USB
Memory	64 MB
Supported Materials	polyester
Dimensions	9.5 x 7.5 x 5.5 inches
Maximum Label Length	Infinite (continuous)