What does 'Head over temp' mean on Brady BMP 61 Label Maker?
If your Brady Label Maker shows a "Head over temp" error, it means the print head is too hot. Allow the print head to cool down for about 10 minutes, then try your print job again.
Why is my Brady BMP 61 Label Maker printing poorly?
If you're getting poor quality prints on your Brady Label Maker, the battery pack may be worn out and not properly holding a charge. Consider ordering a replacement battery pack.
Why is my Brady BMP 61 Label Maker printing with poor quality?
If you're experiencing poor quality printing with your Brady Label Maker, make sure the correct ribbon for the label roll is loaded in the printer.
How to fix 'Ribbon not optimized for label type' error on Brady Label Maker?
If your Brady Label Maker displays an error that the "Ribbon not optimized for label type", the ribbon material type and label material type that are installed in the printer may not be compatible. Replace the ribbon or label supply.
What is the acceptable range for terminal repeat value entered on Brady BMP 61?
The acceptable range for the terminal repeat value is between 0.2 inch and 40 inches.
What should I do if my Brady BMP 61 Label Maker shows an error during printing?
If you get an error while printing on your Brady Label Maker, it could be because the printer cover was opened during printing or feeding. Reinstall the ribbon and label supply, and then press the [CLEAR/ESC] key to clear the error.
Why will my Brady Label Maker not feed labels?
If your Brady Label Maker will not feed labels, the leading edge of the label roll may not be inserted far enough or may be uneven. Ensure the leading edge is securely under the ribs, up to the black line. If the edge is torn, use scissors to cut a straight edge.
What does 'Error - "Out of Media"' mean on my Brady BMP 61?
If your Brady Label Maker displays the error 'Error - "Out of Media"', it means the label/media supply is exhausted, the labels/media are not installed correctly, the notch sensors are dirty, or the label/media memory device has counted down to zero. To solve this, replace the label/media roll or the roll holder, reinstall the labels/media, or clean the sensors. Press [CLEAR/ESC] key to clear the error.
How to fix 'Top of form' error on Brady BMP 61 Label Maker?
If your Brady Label Maker displays a "Top of form" error, a label supply or ribbon has caused a jam. Clear any jams by opening the printer cover.
What to do if the cutter does not cut on my Brady BMP 61 Label Maker?
If your Brady Label Maker cutter does not cut, it is possibly due to adhesive buildup. Clean the cutter blades using a moistened swab from the cleaning kit.
Overview of the BMP®61 label printer, its features, and initial setup instructions.
Details on power sources, battery handling, AC adapters, and connecting the printer to a PC or external devices.
Instructions for loading and unloading label media and ribbon cartridges.
Guide on how to attach the carrying strap and other accessories for printer use.
Steps for entering, editing, clearing, and managing text content on labels.
Customizing font size, attributes, expansion, condensation, and superscripts/subscripts.
How to insert predefined symbols and personal graphics into label designs.
Defining label areas, justification, rotation, frames, and adding barcode elements.
Using serialization for sequential numbering and the List function for variable data.
Saving, opening, deleting, and organizing label files and folders.
Procedures for printing labels, using print preview, and managing print jobs.
Introduction to the various label types supported by the BMP®61 printer.
Detailed guides for using General, WireMarker, Flags, Terminal Block, Vial, and other label types.
Instructions for cleaning the display screen and internal printer components.
Diagnosing and resolving problems related to hardware, power, print quality, and media.
Supported keyboard layouts and language options for different regions.
Categorized list and usage of symbols for various label applications.
General| Print Technology | Thermal Transfer |
|---|---|
| Resolution | 300 dpi |
| Display | Color LCD |
| Cutter | Automatic |
| Keyboard Type | QWERTY |
| Battery | Rechargeable Li-ION battery |
| Max Print Width | 1.5 inches |
| Label Width Range | 0.25 to 1.5 inches |
| Print Speed (mm/s) | 33.8 |
| Connectivity | USB, Wi-Fi |
| Power Source | Battery or AC adapter |
| Supported Materials | Polyester, vinyl, nylon, and more |
| Memory | 256 MB |
| Material Compatibility | Continuous Tapes, Die-Cut Labels |
To Next Page
