EasyManuals Logo

Briggs & Stratton FORTRESS Series User Manual

Briggs & Stratton FORTRESS Series
36 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #34 background imageLoading...
Page #34 background image
34
8. Install the 15 Amp fuse into the fuse holder at top of the
control box.
9. Install the roof.
10. Restore utility power to the generator.
11. Push the ON/OFF Switch on the side of the generator to
the “ON” (I) position.
12. Set the generator mode to AUTO.
Troubleshooting
The service alarm descriptions and their causes are listedin
the table of the "Alarms" section insidethe online"Operation
InstructionsGC1031GENSET Controller"manual(part
number80086364)
FCC Part 15 Information to User
Pursuant to part 15.21 of the FCC Rules, you are cautioned
that changes or modifications to the product not expressly
approved by Briggs & Stratton could void your authority to
operate the product.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV
technician for help.
Troubleshooting
PROBLEM CAUSE CORRECTION
Engine is running, but no AC output is available.
1. Circuit breaker is open or defective.
2. Alarm on generator control board.
3. Poor wiring connections or defective transfer
switch.
1. Reset or replace circuit breaker.
2. Refer toAlarms section
insidethe online"Operation
InstructionsGC1031GENSET
Controller"manual(part number80086364).
Contact local service facility.
3. Check and repair or contact local service
facility.
Engine runs well at no-load but “bogs down” when
loads are connected.
1. Generator is overloaded.
2. Short circuit in a connected load.
3. Shorted generator circuit.
4. Fuel pressure or mixture is incorrect.
5. Kinked fuel line between regulator and
engine.
6. Clogged air filter.
1. Remove one or more loads.
2. Disconnect shorted electrical load.
3. Contact local service facility.
4. SeeGaseous Fuel Systemin this manual.
5. Remove kink. Replace if necessary.
6. Clean or replace air filter.
Engine will not start; or starts and runs rough
1. 15 Amp fuse missing or blown.
2. Thermal fuse(s) blown.
3. Fuel supply turned off or depleted.
4. Incorrect fuel selection.
5. Failed battery.
6. Clogged air filter.
7. Throttle linkage binding
1. Install (new) 15 Amp fuse. SeeSystem
Control Board
2. Replace thermal fuse(s).
3. Open fuel valve(s); check propane tank.
4. Check fuel selector switch and set to proper
setting. (If applicable)
5. Replace battery.
6. Clean or replace air filter.
7. Check linkage.
Engine shuts down during operation.
1. Fuel supply turned off or depleted.
2. Control board digital display shows an
alarm.
1. Check fuel valves, fill propane tank.
2. Refer toAlarms section
insidethe online"Operation
InstructionsGC1031GENSET
Controller"manual(part number80086364).
Not for
Reproduction

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Briggs & Stratton FORTRESS Series and is the answer not in the manual?

Briggs & Stratton FORTRESS Series Specifications

General IconGeneral
BrandBriggs & Stratton
ModelFORTRESS Series
CategoryInverter
LanguageEnglish

Related product manuals