How to fix lower thread winding to one side on Brother BAS-326H-484 Sewing Machine?
If the lower thread winds to one side on your Brother Sewing Machine, adjust the height of the bobbin winder tension assembly.
What to do if my Brother Sewing Machine is skipping stitches?
Skipped stitches on your Brother Sewing Machine can occur for several reasons. Check if the rotary hook tip is missing and replace it if needed. Ensure you're using the correct needle for your fabric; a needle that is too thin can cause this issue. Also, inspect the needle for bending and replace it if bent, and make sure it is installed correctly. Adjust the needle clearance and timing if necessary. If the material is flapping, try a needle hole plate with a smaller diameter. You may also consider using a thinner feed plate or adjusting the intermittent height of the intermittent presser foot, and processing the work clamps and the feed plate into shapes that can hold the material near the seam.
Why does the needle keep breaking on my Brother BAS-326H-484?
If your Brother Sewing Machine's needle breaks, it could be due to several reasons. Start by checking if the needle is bent and replace it if necessary. Ensure you are using a needle suitable for the sewing conditions; a needle that is too thin can easily break. Check if the needle is touching the rotary hook tip and adjust the needle clearance if needed. Incorrect timing between the needle and rotary hook can also cause breakage, so adjust the timing accordingly. You might also need to advance the feed timing.
How to fix a Brother BAS-326H-484 that won't start?
If the Brother Sewing Machine does not start, check whether the machine head switch cord is disconnected. Also, adjust the position of the machine head switch. If the machine head switch is malfunctioning, replace it.
Why is the lower thread breaking on my Brother BAS-326H-484 Sewing Machine?
If the lower thread is breaking on your Brother Sewing Machine, inspect the needle hole plate or bobbin case for any damage. If damage is found, repair the part by buffing it, or replace it. Also, check the lower thread tension and reduce it if it is too strong.
What to do if the upper thread is not cut on my Brother BAS-326H-484?
If the upper thread is not cut on your Brother Sewing Machine, the movable knife may be blunt, requiring replacement. Alternatively, the fixed knife might be blunt and needs sharpening or replacement. Check if the movable knife is picking up the upper thread; if not, adjust the timing or the standby position of the movable knife. If the movable knife is skipping the needle thread due to skipped stitches, refer to the troubleshooting steps for 'Skipped stitches occur'.
Why is the upper thread not tight on my Brother BAS-326H-484 Sewing Machine?
If your Brother Sewing Machine's upper thread is not tight, several factors could be responsible. Ensure that the needle is appropriate for the sewing conditions and that the hole diameter in the needle hole plate isn't too small. A feed plate that is too thin could also be the cause, so consider using a thicker one. For machines with specific specifications, check the hole diameter of the intermittent presser foot. Lubricate the sliding parts of the outer rotary hook and inner hook. Inspect for damage or burring on parts like the rotary hook or needle. Adjust the upper and lower thread tensions, and the thread take-up spring tension. Make sure that the upper thread releases correctly from the hook stopper, and adjust the feed timing or the intermittent height of the intermittent presser f...
How to adjust lower thread winding amount on Brother BAS-326H-484 Sewing Machine?
If the lower thread winding amount is incorrect on your Brother Sewing Machine, adjust the position of the bobbin presser.
What to do if the lower thread is not tight on my Brother BAS-326H-484 Sewing Machine?
If the lower thread is not tight on your Brother Sewing Machine, increase the lower thread tension or reduce the upper thread tension.
Why is the upper thread trailing length irregular on my Brother BAS-326H-484 Sewing Machine?
If the upper thread trailing length is irregular on your Brother Sewing Machine, the movable or fixed knife may be blunt, requiring replacement or sharpening. Additionally, the sub-tension or thread take-up spring tension may be too weak, requiring adjustment.
Explains safety indications and their meanings for safe operation.
Specifies environmental conditions for proper sewing machine operation.
Details safety measures required during machine installation.
Highlights warnings for dangerous voltage and moving parts.
Diagram detailing table processing for machine installation.
Step-by-step guide for installing the control box.
Instructions for mounting and securing the machine head.
Procedure for connecting the ground wire for safety.
Procedure for connecting the power cord to the electrical outlet.
Procedure for correctly installing the sewing needle.
Detailed steps for threading the upper thread correctly.
Guidance on adjusting upper and lower thread tension.
Instructions for starting and performing sewing.
How to use the emergency stop switch to halt operations.
Procedure for cleaning the rotary hook assembly.
Steps for draining oil and checking the regulator.
Procedure to check the machine head switch status.
Guide for setting the timing between needle and rotary hook.
Instructions for replacing knives and adjusting air pressure.
Details errors related to switches and their remedies.
Details errors related to the motor and their remedies.
Details errors related to the feed mechanism and their remedies.
Details errors related to communication and memory.
General| Brand | Brother |
|---|---|
| Model | BAS-326H-484 |
| Category | Sewing Machine |
| Language | English |
To Next Page
