Brother DCP-1623W

 
1-101-10
 Confidential Confidential
3
3.. EERRRROOR IR INNDDIICCAATTIIOONNSS
33..11 EErrrroor r CCooddeess
Errors in the shaded columns do not usually occur during normal use. The possible causesErrors in the shaded columns do not usually occur during normal use. The possible causes
are noise around the installation site, fluctuation of the power supply voltage, and failures inare noise around the installation site, fluctuation of the power supply voltage, and failures in
the software.the software.
ErrorError
codescodes
ProblemProblem
ReferRefer
to:to:
ErrorError
codescodes
ProblemProblem
ReferRefer
to:to:
01000100
 --
04010401
Cannot detect the synchronizedCannot detect the synchronized
signal of the polygon motor forsignal of the polygon motor for
the laser unit.the laser unit.
1-23
1-23
02010201
The speed of the main motorThe speed of the main motor
does not stabilize within thedoes not stabilize within the
specified time.specified time.
1-231-23 04020402
 --
02020202
 --
04050405
 --
02030203
 --
05010501
The center thermistor of theThe center thermistor of the
fuser unit has not reached thefuser unit has not reached the
specified temperature within thespecified temperature within the
specified time.specified time.
1-24
1-24
02040204
 --
05020502
The center thermistor has notThe center thermistor has not
reached the specifiedreached the specified
temperature within the specifiedtemperature within the specified
time after the fuser unit hastime after the fuser unit has
reached to a certain temperature.reached to a certain temperature.
1-24
1-24
02050205
 --
05030503
The center thermistor of theThe center thermistor of the
fuser unit detected afuser unit detected a
temperature higher than thetemperature higher than the
specified value.specified value.
1-24
1-24
02060206
 --
05040504
After the heat unit was heatedAfter the heat unit was heated
normally, the center thermistor ofnormally, the center thermistor of
the fuser unit detected athe fuser unit detected a
temperature lower than thetemperature lower than the
specified value.specified value.
1-24
1-24
02070207
 --
05050505
The center thermistor of the fuserThe center thermistor of the fuser
unit detected a temperature riseunit detected a temperature rise
greater than the specified valuegreater than the specified value
within the specified time.within the specified time.
1-24
1-24
02080208
 --
05060506
The center thermistor of the fuserThe center thermistor of the fuser
unit detected a temperature fallunit detected a temperature fall
greater than the specified valuegreater than the specified value
within the specified time.within the specified time.
1-24
1-24
02090209
 --
05080508
The side thermistor of the fuserThe side thermistor of the fuser
unit did not reach to the specifiedunit did not reach to the specified
temperature when the heatertemperature when the heater
was ON.was ON.
1-251-25
03000300
Cannot detect the lock signal ofCannot detect the lock signal of
the polygon motor for the laserthe polygon motor for the laser
unit (second time).unit (second time).
1-231-23 050A050A
The hardware detected that theThe hardware detected that the
center thermistor of the fuser unitcenter thermistor of the fuser unit
indicated a temperature error.indicated a temperature error.
1-251-25
03050305
 --
050B050B
When the temperature of theWhen the temperature of the
center thermistor of the fuser unitcenter thermistor of the fuser unit
is lower than the idle temperature,is lower than the idle temperature,
the side thermistor of the fuserthe side thermistor of the fuser
unit detected a temperatureunit detected a temperature
higher than the specified value.higher than the specified value.
1-25
1-25