28
of several types of maintenance required on your spa, including
rinsing the lter, cleaning the lter, changing spa water, and
2-year professional maintenance checks. Each task has its own
standard duration, based on normal use.
From the Settings page you can access the Maintenance menu,
which gives you access to the following options:
• Maintenance reminders
• Standby mode
Maintenance reminders menu allows you to verify the time left
before maintenance is required, as well as to reset the time once a
task is completed.
Use the
and buttons to choose the maintenance
reminder that you wish to view. Select it by pressing the
(Light) button. To reset a reminder once maintenance has been
performed select it by pressing the (Light) button, then
conrm it is “Done” by pressing the (Jets 2/Key 2) button
when prompted. Once you have conrmed the task reminder will
be reset.
Selecting the Standby mode from the maintenance submenu
allows you to service your spa. Pumps will stop for 30 minutes,
and automatically restart after this time. Once Standby mode
has been activated a screen will appear to show that pumps are
stopped. e Home/Status page will return after the 30 minute
standby maintenance period.
Use the (Light) button to Cancel the Standby function before
the 30 minute period and restart the spa.
Set Date and Time of Day
Setting the correct date and time is important for settings to
function as expected. Upon restarting your spa adjust the time
format (24 hr. or AM/PM), change the year, date, and time as
needed.
Within the Settings menu use the (Light) button to select
the Date & Time submenu.
Use the and buttons to choose the setting that
you wish to adjust, and select it by pressing the (Light)
button. Use the and buttons to change the parameters,
and the (Light) button to cycle between options. e
(Settings) button will take you back to the main Settings menu.
Adjust Keypad Settings
In this Settings submenu you can change the temperature unit,
language, display orientation, and keypad security.
Within the Settings menu use the and buttons and then
the (Light) button to select the Keypad Settings submenu.
Use the and buttons to choose the setting that you wish
to adjust, and select it by pressing the (Light) button. Use
the and buttons to change the parameters, and the
(Light) button to move between options. e (Settings)
button will take you back to the main Settings menu.
When you change the display orientation, the contextual options
and arrow keys adjust to the chosen orientation. e Mode and
Menu keys remain unchanged, as well as the accessory keys
in the main spa menu.
Screen Lock Settings
You can lock the keypad by selecting one of 3 security levels:
Unlock, Partial lock, or Full lock. e Partial level locks the set
point adjustment and many options in the settings menu. e
Full level locks all keypad functions. Once you have selected your
desired lock function press the (Jets 1/Key 1) button. e
display will prompt you to press and hold the (Light) button
for 5 seconds to activate the keypad lock function. To unlock
the keypad (either Partial or Full), press and hold the (Light)
button for 5 seconds.
IMPORTANT: Please do not make changes in this section
unless you are a qualied electrician.
In this section you can change the low-level conguration, as
well as modify the number of phases and the input current
value.* Please refer to the diagram on the spa control center box,
located inside of the equipment compartment, for the default
conguration of your specic spa model.
Press the (Light) button to access the submenu, a warning
will appear. Press the (Light) button for 5 seconds when
prompted to access the submenu options. Use the and
buttons to move to the selection you want to modify. Use the
(Light) button to select, and the and buttons to move
through the selections. Press the (Light) button again to
conrm.
Please see the techbook for your spa system for details on low-
level settings. Once you have changed the number of phases in
the menu you will be unable to use the and buttons to
return to the Low-level conguration menu. Please go back and
access the Conguration menu again.
NOTE: On initial connection the installer is prompted for
electrical congurations. e Low-Level setting is selected by the
installer. e Phase and Amperage is set automatically. Default
settings should be conrmed by the installer to match the actual
phase and amperage at the spa’s installation location. In rare
occassions it may be necessary to adjust the Phase and Amperage
setting to match the actual service available at the installation
location using the instructions above.
* Depending on pack conguration, a code may be required
to change the low level number, number of phases or input
current. is code is “5555”.
When you select Restore you will be asked to conrm your
choice. Doing so will reset all settings to factory default.
Following a restore you will be asked to choose your audio source
Use the and buttons to choose between in.stream,
in.stream 2, in.tune and no/other audio. is should only be
To Next Page
Loading...
