To Next Page
A
Angela CarrilloAug 18, 2025
How to fix my BWT Perla Silk L regenerating at the wrong time?
- LLinda AyersAug 18, 2025
If your BWT Water Dispenser regenerates at the wrong time, check if the present time is correct and reset it if necessary.
How to fix my BWT Perla Silk L regenerating at the wrong time?
If your BWT Water Dispenser regenerates at the wrong time, check if the present time is correct and reset it if necessary.
What to do if my BWT Water Dispenser electronic display shows error code “SALt”?
If your BWT Water Dispenser's display shows the error code “SALt” and an audible alarm sounds, fill the brine cabinet with salt. Then, press the [SET] key to reset the salt alarm to the full capacity of salt.
What to do if my BWT Perla Silk L Water Dispenser electronic display shows error code “Err 1”?
If the display shows error code “Err 1” and an audible alarm sounds, check that all the connections are secure. Turn the power off for 15 seconds until PF is no longer displayed, then turn it back on to allow the system to reset.
Why does my BWT Perla Silk L Water Dispenser unit regenerates at the wrong time?
If your BWT Water Dispenser regenerates at the wrong time, check if the present time is correct and reset it if necessary.
How to fix hard water from my BWT Perla Silk L Water Dispenser?
If the water from your BWT Water Dispenser is still hard, make sure to fill the brine cabinet with salt. Also, switch the power on and check the connections, or change the battery if it's battery operated. Ensure that the by-pass valve is closed and the inlet and outlet valves are open, or operate uniconnect. If needed, reset the hardness setting.
What to do if the water level in my BWT Perla Silk L Water Dispenser's brine cabinet overflows?
If the water level in the brine cabinet of your BWT Water Dispenser is overflowing, first check if the line pressure is within the specified range of 1.7 - 5.0 bar for UK by connecting a pressure gauge to a water outlet. If the pressure falls outside this range, install a pressure reducing valve or booster pump as needed. Also, inspect the drain line to ensure it is not kinked, blocked, or frozen. Finally, check that the power is on and connections are secure, especially after a power interruption.
Why is my BWT Perla Silk L Water Dispenser constantly draining water?
If water constantly runs from the drain of your BWT Water Dispenser, check if the unit is in recharge mode; if so, this is normal, and you should wait until the recharge is complete. Otherwise, ensure the power is on and all connections are secure, or replace the battery if it's battery operated.
What to do if my BWT Perla Silk L Water Dispenser has no water coming out?
If there is no water coming from your BWT Water Dispenser, first, open the mains stop valve. Then, open the inlet and outlet valves to the water softener, or operate uniconnect.
What causes excessive salt usage in my BWT Water Dispenser?
If your BWT Water Dispenser is using excessive salt, reduce the hardness setting if it is incorrect.
What to do if my BWT Perla Silk L water level in brine cabinet reaches overflow?
If the water level in your BWT Water Dispenser's brine cabinet is overflowing: * Check if the line pressure is within the water softener's specification by connecting a pressure gauge to a water outlet. Ensure the pressure is between 1.7 - 5.0 bar for UK. * If the pressure falls outside the specification, fit a pressure reducing valve or booster pump. * Inspect the drain line to ensure it is not kinked, blocked, or frozen. * Verify that the power is on and all connections are secure.
Covers electrical safety, protection from extreme temperatures, cleaning warnings, and operating precautions.
Guides users through setting the time of day, water hardness, and recharge time.
Covers site preparation, positioning, national guidelines, frost protection, electrical interference, and hard water analysis.
Details unit handover, initial checks, and connection procedures.
Discusses loft installation, plumbing systems, backflow prevention, drinking water, and pressure.
Provides detailed steps for physical installation, including positioning, connections, and salt filling.
Covers power loss, flow indicators, cleaning, manual regeneration, adding salt, and cabinet water level.
Provides a checklist for common problems like hard water, overflow, no water, and display errors.
General| Brand | BWT |
|---|---|
| Model | Perla Silk L |
| Category | Water Dispenser |
| Language | English |
