Byron BY103 - User Manual

1: Place a small flat screwdriver
into the locking clip on the
base of the Bell Push.
2: Gently twist.
3: The backing plate will unclip.
1
Functions:
4 Selectable Melodies
1: Ding Dong (Repeat) 3: Alarm
2: Westminster 4: Ding Dong Ding
4
To select a melody for the Door Chime
1: Remove the Back Plate from the Bell
Push.
2: Press the Melody Select button.
3:The chime will play the newly selected
sound.
4: Press again to select the next melody.
Note: For Front/Back door setup, select a
different melody in one of the Bell Pushes.
CR2032
Adding Additional Chime/Bell Push:
1: Insert CR2032 battery
(Supplied) into the battery
holder.
2: Make sure the positive side
is facing upwards.
3: Replace back plate.
2
Warning: Make sure that the batteries are
replaced correctly to avoid battery failure.
Only replace with same or equivalent type.
3
1: Plug Chime into a UK 3pin
socket, 220 – 240V ~ 50Hz.
2: Switch the socket on.
Beep
Beep
1: The Chime will ‘Beep Beep’.
2: Press the Bell Push within
60 seconds to learn the
Bell Push to the chime.
3: The Chime will ring to
confirm setup.
Note: Maximum of 2
Bell Pushes can be learnt to a
single Chime for Front/Back
4
Additional Bell Push
To add an additional Bell Push to the Door Chime kit
1: Unplug the Door Chime and wait for 10
seconds.
2: Plug the Door Chime into the Socket and
switch the socket on.
3: Press both Bell Pushes within 60 seconds, to pair
the additional Bell Push to the Chime.
4: Chime will ring to confirm setup, wait 60 seconds
for Chime to exit the learn mode before repressing the
Bell Push5.
5: For Front/Back door setup, select a different melody in one of the
Bell Pushes - See Melody Selection.
Note: Maximum of 2 Bell Pushes can be learnt to a single
Door Chime.
Front Door
Back Door
New Chime
Additional Chime
To add an additional Chime unit to the Door Chime kit
1: Unplug the NEW Door Chime and wait for 10
seconds
2: Plug the Door Chime into the Socket and switch the socket On.
3: The Chime will ‘Beep Beep’ to indicate that it has entered
the Learn mode.
4: Press the Bell Push within 60 seconds, to pair the additional
Chime to the Bell Push.
5: Chime will ring to confirm setup, wait 60 seconds for the Chime
to exit the learn mode before repressing the Bell Push.
Beep
Beep
BY103
1: Push Button 5: Plug-through Chime
2: Melody Selector 6: Speaker
3: Bell Push Battery
4: Signal Sent LED
1:
2:
4:
:3
6:
5:
3
Plug-in any standard electrical product,
220–240V ~50Hz.
e.g. table light, upto a Max Load of
1000W
Avoid using low voltage Transformers, as
this may reduce the operating range of
the Door Chime
Plug-through Socket:
Melody selection:
™
Plug-through
Wire Free Chime Kit

Summary

Setup and Installation

Bell Push Battery Compartment Access

Instructions for opening the bell push to access the battery compartment via a small screwdriver.

Bell Push Battery Installation

Steps for inserting the CR2032 battery, ensuring the positive side faces upwards.

Chime Unit Power Connection

Guide to plugging the chime unit into a UK socket and switching it on.

Chime Functions and Operation

Melody Selection Process

Procedure to select one of the four available melodies for the door chime using the bell push.

Plug-through Socket Functionality

Details on using the plug-through socket for other electrical devices, including load limits.

Adding Components to System

Pairing Additional Chimes

Steps to learn and pair a new chime unit to the existing door chime system.

Pairing Additional Bell Pushes

Guide to learn and pair new bell pushes, including setup for front/back doors.

Bell Push Installation and Battery Care

Bell Push Mounting

Instructions for mounting the bell push using screws or adhesive tape.

Bell Push Battery Replacement

Guide to replacing the CR2032 battery in the bell push and proper disposal.

Chime Unit Installation and Range

Chime Unit Placement

Guidance on placing the chime unit within its operating range and avoiding interference.

Range Considerations

Information on factors affecting the wireless signal range, such as walls and metallic surfaces.

Troubleshooting and Important Notes

Troubleshooting Common Issues

Advice on addressing issues like the chime not sounding, checking batteries and pairing.

Safety and Appliance Usage

Important safety warnings, including appliance usage by children and serviceability.

Byron BY103 Specifications

General

Brand	Byron
Model	BY103
Category	Accessories
Language	English