Byron BY202 - User Manual

™
Plug-in
Wire Free Chime Kit
BY202
1: Push Button 5: Plug-in Chime
2: Melody Selector 6: Speaker
3: Bell Push Battery 7: Volume control
4: Signal Sent LED
1:
2:
4:
:3
1: Place a small flat screwdriver
into the locking clip on the
base of the Bell Push.
2: Gently twist.
3: The backing plate will unclip.
1
To select the Chime Volume level, press the ‘VOL’
button on the chime There are 4 selectable volume
levels, the Door Chime is pre-set to the loudest
volume setting.
Volume
Default
Functions:
6 Selectable Melodies
1: Tubular 3-Note 4: Solo
2: Big Ben 5: Tubular Score
3: Tubular 2-Note 6: Clarinet
4
Beep
Beep
To select a melody for the Door Chime
1: Remove the Back Plate from the Bell
Push.
2: Press the Melody Select button.
3:The chime will play the newly selected
sound.
4: Press again to select the next melody.
Note: For Front/Back door setup, select a
different melody in one of the Bell Pushes.
CR2032
6:
7:
5:
1: plug Chime into a UK 3pin
socket, 220 – 240V ~ 50Hz.
2: Switch the socket on.
3: Chime will ‘Beep’ on Start up.
3
1: Press and hold the ‘VOL’
button on the Door Chime,
until the Chime goes
‘Beep Beep’ (6 Seconds).
2: Press the Bell Push within
60 seconds to learn the
Bell Push to the chime.
3: The Chime will ring to
confirm setup.
Note: Maximum of 6 Bell
Pushes can be learnt to a
single Chime.
4
New Chime
Additional Chime
To add an additional Chime unit to the Door Chime kit
1: Press and hold the ‘VOL’ button on your New Door Chime, until the
Chime goes ‘Beep Beep’ (6 Seconds)
2: Press the Bell Push within 60 seconds to learn the additional
Chime to the Bell Push.
3: Chime will ring to confirm setup, wait 60 seconds for the Chime to
exit the learn mode before repressing the bell push.
Additional Bell Push
To add an additional Bell Push to the Door
Chime kit.
1: Press and hold the ‘VOL’ button on your
Door Chime, until the Chime goes
‘Beep Beep’ (6 Seconds).
2: Press the Bell Push within 60 seconds
to learn the additional Bell Push to the
Chime.
3: Chime will ring to confirm setup, wait 60 seconds for the Chime
to exit the learn mode before repressing the bell push.
For Front/back door setup, select a different melody in one of
the Bell Pushes - See Melody Selection.
Note: Maximum of 6 Bell Pushes can be learnt to a single Chime
Adding Additional Chime/Bell Push:
Beep
Beep
Front Door
Back Door
1: Insert CR2032 battery
(Supplied) into the battery
holder.
2: Make sure the positive side
is facing upwards.
3: Replace back plate.
2
Warning: Make sure that the batteries are
replaced correctly to avoid battery failure.
Only replace with same or equivalent type.

Summary

Setup Procedures

Installing the Bell Push Battery

Guide to inserting the CR2032 battery and replacing the back plate.

Plugging in the Chime Unit

Instructions for connecting the chime unit to a power socket.

Melody Selection Functions

Selecting a Chime Melody

Steps to choose one of the six selectable melodies for the chime.

Available Melody Options

List of available chime melodies including Tubular 3-Note, Big Ben, etc.

Volume Control Function

Adjusting Chime Volume Levels

How to set the chime volume across four selectable levels.

Adding Additional Devices

Adding an Additional Chime Unit

Procedure to pair a new chime unit with the existing bell push.

Adding an Additional Bell Push

Steps to pair an extra bell push to the chime unit for multi-door setups.

Bell Push Installation Guide

Mounting the Bell Push

Detailed instructions for attaching the bell push to a wall or surface.

Alternative Bell Push Mounting

Mentions using adhesive tabs or tape as an alternative to drilling.

Chime Installation Guide

Chime Placement and Range

Guidance on positioning the chime unit for optimal wireless signal range.

Maintenance and Reset Procedures

Changing Bell Push Batteries

Procedure for replacing the CR2032 battery in the bell push.

Resetting the Chime Unit

Instructions to restore the chime unit to its default factory configuration.

Troubleshooting and Product Details

Troubleshooting Common Issues

Advice for common problems like no sound, battery issues, or range reduction.

Product Specifications

Technical details including device type, weather resistance, power requirements, and operating range.

Support Contact Information

Details for customer support, website, and company address.

Byron BY202 Specifications

General

Brand	Byron
Model	BY202
Category	Accessories
Language	English