CAB MAESTRO 4S - Cutting Recommendations

10
6.3 Recommendation for cutting - depend of notch thickness and number of cuts
notch thickness
i
Notice!
The cutting is more gentle for the PCB's with a higher number of
cuts.
The deepness of the last cut must be so that the PCB's are easily to
separate.
The values are recommendation and it's possible to change it if it is
necessary.
Notch Thickness 0,8 mm
Number of cuts to separating
PCB's
1. Cut 2. Cut 3. Cut 4. Cut 5. Cut
5 0,65 mm 0,50 mm 0,30 mm 0,15 mm 0,00 mm
4 0,65 mm 0,40 mm 0,20 mm 0,00 mm -
3 0,60 mm 0,40 mm 0,20 mm - -
2 0,55 mm 0,25 mm - - -
1 0,40 mm - - - -
Notch Thickness 0,7 mm
Number of cuts to separating
PCB's
1. Cut 2. Cut 3. Cut 4. Cut 5. Cut
5 0,60 mm 0,40 mm 0,30 mm 0,15 mm 0,00 mm
4 0,55 mm 0,35 mm 0,20 mm 0,00 mm -
3 0,55 mm 0,35 mm 0,20 mm - -
2 0,45 mm 0,25 mm - - -
1 0,35 mm - - - -
Notch Thickness 0,6 mm
Number of cuts to separating
PCB's
1. Cut 2. Cut 3. Cut 4. Cut 5. Cut
5 0,50 mm 0,35 mm 0,25 mm 0,10 mm 0,00 mm
4 0,50 mm 0,30 mm 0,15 mm 0,00 mm -
3 0,45 mm 0,30 mm 0,15 mm - -
2 0,40 mm 0,20 mm - - -
1 0,30 mm - - - -
Notch Thickness 0,5 mm
Number of cuts to separating
PCB's
1. Cut 2. Cut 3. Cut 4. Cut 5. Cut
5 0,40 mm 0,30 mm 0,20 mm 0,10 mm 0,00 mm
4 0,40 mm 0,25 mm 0,15 mm 0,00 mm -
3 0,40 mm 0,25 mm 0,15 mm - -
2 0,35 mm 0,15 mm - - -
1 0,25 mm - - - -
Notch Thickness 0,4 mm
Number of cuts to separating
PCB's
1. Cut 2. Cut 3. Cut 4. Cut 5. Cut
5 0,35 mm 0,25 mm 0,15 mm 0,10 mm 0,00 mm
4 0,30 mm 0,20 mm 0,10 mm 0,00 mm -
3 0,30 mm 0,20 mm 0,10 mm - -
2 0,25 mm 0,15 mm - - -
1 0,20 mm - - - -
Notch Thickness 0,3 mm
Number of cuts to separating
PCB's
1. Cut 2. Cut 3. Cut 4. Cut 5. Cut
5 0,25 mm 0,20 mm 0,10 mm 0,05 mm 0,00 mm
4 0,25 mm 0,15 mm 0,10 mm 0,00 mm -
3 0,25 mm 0,15 mm 0,10 mm - -
2 0,20 mm 0,10 mm - - -
1 0,15 mm - - - -
Table 4 Recommendation for cutting
6 Switch on and Programming