Calpeda CT Series User Manual

Calpeda CT Series

16 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

Page

2

English

Página

8

Español

Close coupled peripheral pumps

Bombas monobloc con rodete periférico

CT, T, TP

OPERATING INSTRUCTIONS

INSTRUCCIONES DE USO

Questions and Answers:

A
Andrew Schneider Jr.Aug 17, 2025
Why is there insufficient flow from my Calpeda CT?
- D
  dale18Aug 17, 2025
  Insufficient flow from your Calpeda Water Pump can stem from several issues. Start by checking if the pipes and accessories have a diameter too small, causing excessive head loss; if so, use appropriately sized pipes. Also, inspect the rotor for deposits or solid bodies blocking internal passages; clean the rotor and install a suction filter. Check the rotor and pump casing for wear, and replace them if necessary. Ensure the liquid's viscosity isn't too high for the pump, and verify the pump's rotation direction is correct by checking the electrical connections. Reduce suction head if it's excessive, and shorten the suction pipe or use a wider diameter pipe if it's too long.
J
John SmallAug 23, 2025
How to reduce noise and vibrations from my Calpeda CT Water Pump?
- C
  Chad PerezAug 23, 2025
  To reduce noise and vibrations from your Calpeda Water Pump, start by checking if any solid objects are obstructing the rotor. Inspect the bearings for wear and replace them if needed. Ensure the pump and pipes are firmly attached, anchoring the delivery and suction piping as necessary. If the flow is too strong for the delivery pipe's diameter, use larger diameters or reduce the pump flow. If the pump is functioning in cavitation, reduce the flow by adjusting the feeder gate and/or using pipes with a bigger internal diameter. Verify the mains voltage is correct, and if necessary, realign the pump-motor unit.
E
Eric SmithAug 30, 2025
What to do if my Calpeda CT functions but no water comes out?
- R
  Rachel WalkerAug 30, 2025
  If your Calpeda Water Pump is running but not pumping water, first check for air infiltration from suction tube connections, drain plugs, the pump filling point, or suction pipe gaskets; tighten any loose connections. Next, inspect the foot valve for blockages or ensure the suction pipe is fully immersed in the liquid; clean or replace the valve and use a suitable suction pipe. Finally, check the suction filter for blockages; clean or replace it if necessary.
D
Debra AdamsSep 4, 2025
Why is my Calpeda Water Pump leaking from the mechanical seal?
- C
  Curtis LambSep 4, 2025
  Leakage from the mechanical seal of your Calpeda Water Pump can occur for several reasons. The mechanical seal may have functioned when dry or has stuck. The mechanical seal could be scored by abrasive particles in the pumped liquid. The mechanical seal might be unsuitable for the application. If any of these issues are the cause, replace the seal. If the leakage is a slight initial drip during filling or on first start-up, allow time for the seal to adjust to the shaft's rotation. If the problem persists, consider the other potential issues.

Calpeda CT Series Specifications

General

Brand	Calpeda
Model	CT Series
Category	Water Pump
Language	English

Related product manuals

Preview: Calpeda I

Preview: Calpeda NG

Preview: Calpeda MXS

Preview: Calpeda SPA

Preview: Calpeda MXV-B

Preview: Calpeda NM Series

Calpeda NM Series

Preview: Calpeda MXH Series

Calpeda MXH Series

Preview: Calpeda e-idos META

Calpeda e-idos META

Calpeda MXV-B 40-806

Preview: Calpeda e-idos E-MXPM

Calpeda e-idos E-MXPM

Calpeda e-idos E-NGXM