CAME ZF1 - User Manual

CANCELLI AUTOMATICI
ZF1
Documentazione
Tecnica
S63
rev. 1
10/2002
© CAME
CANCELLI
AUTOMATICI
SERIE Z | Z SERIES | SERIE Z
SCHEDA COMANDO
CONTROL BOARD
TARJETA DE MANDO
ITALIANO—ENGLISH—ESPAÑOL
ITALIANO/ ENGLISH/ ESPAÑOL
319S63-1
21
PROG
CARATTERISTICHE GENERALI
ITALIANO
DESCRIZIONE
La scheda comando ZF1 è adatta al
comando di automazioni per cancelli a
battente della serie ATI, FERNI, FAST,
KRONO, alimentata a 230V con
potenza fino a 320W,frequenza 50÷60
H
z
.
Progettata e costruita interamente
dalla CAME S.P.A., risponde alle
vigenti norme di sicurezza.
La scheda va inserita nel contenitore
in ABS (S4339 o S4340), con grado di
protezione IP54, dotato di presa per il
riciclo d’aria e di relativo trasformato-
re.
La scheda deve essere alimentata a
230V (a.c.) sui morsetti L1 e L2, ed é
protetta in ingresso con un fusibile da
5A, mentre gli accessori a bassa
tensione (24V) sono protetti con
fusibile da 3.15A.
La potenza complessiva degli acces-
sori (24V) non deve superare i 20W.
GENERAL CHARACTERISTICS
ENGLISH
DESCRIPTION
The ZF1 control board is used to
command automations for swing gates
belonging to the ATI, FERNI, FAST and
KRONO series, powered at 230V with
rated power up to 320W, 50-60 H
frequency
z
.
Fully designed and built by CAME S.p.A.,
it meets the safety regulations in force.
The board should be inserted into the
container made of ABS (S4339 or
S4340), with IP54 protection, equipped
with intake for air recycling and related
transformer.
The board must be powered at 230V
(a.c.) on the L1 and L2 terminals, and
the inlet is protected with a 5A fuse,
while the low voltage (24V) accessories
are protected with a 3.15A fuse.
The accessorie's total capacity (24V)
should not exceed 20W.
CARACTERISTICAS GENERALES
DESCRIPCIÓN
La tarjeta de mando ZF1 es adecuada
para accionar automatizaciones para
cancelas de batiente de la serie ATI,
FERNI, FAST, KRONO, alimentada a
230V con potencia hasta 320W,
frecuencia 50÷60 Hz.
Diseñada y fabricada completamente
por CAME S.P.A., responde a las
normas de seguridad vigentes.
La tarjeta se monta en la caja de ABS
(S4339 o S4340), con clase de
protección IP54, dotada de toma para
recirculación de aire y del
transformador respectivo.
La tarjeta se debe conectar a 230V
(c.a.) en los bornes L1 y L2, y está
protegida a la entrada con un fusible
de 5A, mientras que los accesorios de
baja tensión (24V) están protegidos
con un fusible de 3,15A.
La potencia total de los accesorios
(24V) no tiene que superar los 20W.
ESPAÑOL

CAME ZF1 Specifications

General

Brand	CAME
Model	ZF1
Category	Control Systems
Language	English

Summary

General Characteristics

Description

Provides a description of the ZF1 control board's suitability for swing gates and its compliance with safety standards.

Safety Features

Optional Accessories

Lists optional accessories that can be connected to the control board, such as electric locks and pilot lamps.

Other Functions

Details additional functions like automatic closing and the 'operator present' mode for gate operation.

Adjustments

Covers settings for automatic closure time, motor delay, and operating time.

Base Board Components

Main Components List

Identifies and lists the main components and terminals on the base board with their corresponding functions.

Electrical Connections

Function Selections

Adjustments

Remote Control Programming

AF Board Insertion

Instructions for inserting the AF radiofrequency board into the motherboard.

Transmitter Encoding

Standard Encoding Procedure

Details the common procedure for encoding transmitters using jumpers and buttons.

T262 M;T302 M Transmitter Configuration

Configuration steps for T262M/T302M transmitters, including initial channel settings.

T2622 M;T3022 M Transmitter Configuration

Configuration steps for T2622M/T3022M transmitters, detailing channel assignments.

ATOMO Transmitter Instructions

References separate instruction sheets for ATOMO transmitter configurations.

TOP Transmitter Configuration

Details setting the code and channel for TOP transmitters using dip-switches.

T434 M;T314 M Transmitter Configuration

Instructions for setting only the code for T434M/T314M transmitters.

TAM;TFM Transmitter Instructions

References separate instruction sheets for TAM and TFM transmitter configurations.

Code Storage

Motor Torque Limiter

Manufacturers Declaration