Canton Smart Amp 5.1 Operating Instructions

3
23
English
22
English
USING AirPlay 2 TECHNOLOGY
Note: AirPlay resp� AirPlay 2 is only available on devices of the second generation (Amp 5�1 S2)�
With Apple AirPlay technology, you can play audio content over the wireless network (WLAN) using your Smart Amp 5�1�
Additionally, AirPlay 2 technology offers you the possibility to play your content on several loudspeakers and/or amplifiers synchronously�
Connecting the Smart Amp 5.1 to the WLAN (WiFi network) via iPhone, iPad or iPod touch
To connect your Smart Amp 5�1 to your wireless network (WLAN) via iPhone, iPad or iPod touch, please proceed as follows:
1
Disconnect your Amp 5�1 from the power outlet, wait for at least 30 seconds and reconnect your Amp 5�1 to the mains afterwards�
Now please wait until the display shows [NET] and [SET] and continue with the following steps within max� 10 minutes�
2
On your iPhone, iPad or iPod touch, select „Settings“ and then „Wi-Fi“ (WLAN)�
3
Under the menu item „SET UP NEW AIRPLAY SPEAKER“ select the Smart Amp 5�1 as the device to be installed�
4
The „AirPlay Config���“ window opens�
a� Under „Network“ select the network to which you want to connect the Smart Amp 5�1�
b� Under “Speaker name” enter the name (synonym) you want to assign to the Amp 5�1�
c� Optionally, you can assign a password under „SPEAKER PASSWORD“�
d� Select the function „Next“ and wait (approx� 30 seconds) until the Amp 5�1 shows [WIF] / [CON] in the display�
5
Finalize the registration process in the „Configuration finished“ window that opens by pressing the „Done“ button� The Smart Amp 5�1 is now
connected to your WLAN (Wi-Fi network) and ready for use�
Playback via AirPlay resp. AirPlay 2 technology
Note: AirPlay resp� AirPlay 2 is only available on devices of the second generation (Amp 5�1 S2)�
Requirements to play music using AirPlay 2 technology:
• iPhone, iPad, iPod touch or HomePod with iOS 11�4 or higher�
• Apple TV 4k or Apple TV HD with tvOS 11�4 or higher
• Mac or PC with iTunes 12�8 or higher resp� Mac with macOS Catalina or higher�
Playback on Smart Amp 5�1 (and other devices):
1
To play your music using the Amp 5�1, start the playback of the desired title in a media app on your (mobile) device�
2
Open the Control Center on your Apple device � Swipe from the top right corner (iOS 12 or higher) or from the bottom (iOS 11 or lower) towards
the center of the display�
3
Select the AirPlay symbol in the Audio Card, and in the dialog that opens select the speaker(s) resp� amplifier(s) which you want to use for play-
back�
To start music playback on one or more AirPlay-enabled speaker(s) via Mac, Apple TV or Apple Music, please refer to the following support page:
https://support�apple�com/en-ca/HT202809
Notes: • Use Siri on your iPhone, iPad, HomePod, or Apple TV to control the Amp 5�1 with just your voice�
• The Smart Amp 5�1 supports only audio streaming, no video streaming�

Canton Smart Amp 5.1 Specifications

General

Video in	3x HDMI
Video out	1x HDMI
Ethernet LAN (RJ-45) ports	1
Speakers connectivity type	-
Product color	Black
Volume control	Touch
Cables included	AC
Treble adjustment	Yes
Connectivity technology	Wired & Wireless
Audio decoders	DTS-HD, Dolby Atmos
Audio output channels	- channels
Peak power per channel	600 W
Signal-to-Noise Ratio (SNR)	- dB
Total Harmonic Distortion (THD)	- %

Weight and Dimensions

Depth	154 mm
Width	245 mm
Height	120 mm
Weight	5240 g