Canton Smart Amp 5.1 User Manual (English)

Other manuals for Canton Smart Amp 5.1

Operating Instructions37 pages

Short Manual56 pages

Questions and Answers:

C
Chelsea ClarkSep 13, 2025
How to make Canton Amp 5.1 turn off automatically?
- T
  Timothy NguyenSep 14, 2025
  If your Canton Amp 5.1 is not turning off automatically, it may be because the standby function is set to Manual [MAN]. To enable automatic shutoff, activate the standby function ECO, AUT, or NSB. Also, if the Auto [AUT] standby function is active and the source device transmits a carrier signal even in standby mode (optical or coaxial digital input only), switch off the source device at its mains switch or disconnect it from the mains.
T
Terry SheppardAug 25, 2025
Why is there no sound coming from my Canton Amp 5.1?
- V
  Valerie RitterAug 25, 2025
  If there is no sound from your Canton Amp 5.1, there might be several reasons: * The sound format selected on your source device may be incorrect; please check its settings. * There may be no signal from the player, or the volume is set to "zero"; unlock the digital output on the source device and increase the volume. * The cable may not be connected correctly or is defective; check the connection between the player and the Amp 5.1, and replace the cable if necessary. * Ensure that the protective caps on the connectors of the optical cable (TOSLINK) are removed.
D
Danielle WilliamsAug 25, 2025
How to fix Canton Amp 5.1 remote control not working?
- A
  Angel SmithAug 26, 2025
  If your Canton Amp 5.1 is not responding to the remote control, here are a couple of things to check: 1. Make sure you have removed the protective film on the remote control. 2. The battery may be empty. Replace it, ensuring you use the correct battery type and insert it with the correct polarity.
N
Nancy White MDAug 26, 2025
What to do if Bluetooth playback is interrupted on Canton Amp 5.1?
- W
  William LaraAug 27, 2025
  If you're experiencing no playback or interrupted playback via Bluetooth on your Canton Amp 5.1, consider the following: * Ensure there is a connection between the Amp 5.1 and your mobile device by pairing and connecting them as described in the manual. The mobile device may need to be reconnected. * Increase the volume on both the mobile device (to the maximum possible value) and the Amp 5.1. * Keep sources of interference, such as a WiFi Router or a laptop, away from the Amp 5.1. * If you are using both WiFi and Bluetooth on your mobile device, disable WiFi to prevent potential interference. * Make sure that the distance between the Amp 5.1 and the mobile device is less than 10m.
F
Frederick GordonAug 27, 2025
Why won't my Canton Amp 5.1 turn on?
- T
  Tracy GuzmanAug 27, 2025
  If your Canton Amp 5.1 is not turning on, ensure that the power cable is correctly connected to both the Amp 5.1 and the power outlet, and that it is fully plugged in.
T
Tiffany MendezSep 8, 2025
What does [WLS] mean on my Canton wireless speaker display?
- T
  tgonzalezSep 9, 2025
  If a (slave) speaker shows [WLS] in the display of your Canton Amp 5.1: * The slave speaker may be operated without the Amp 5.1. Turn on the Amp 5.1. * The (slave-) speaker may not be paired anymore. Pair the (slave-) speaker with the Amp 5.1 according to chapter Speaker Config [SPC] / Speaker Mapping [SPM].
J
Jessica ValentineSep 7, 2025
How to make Canton wireless speakers turn on with Amp 5.1?
- J
  jacksonkristiSep 7, 2025
  If paired wireless speakers do not turn on together with the Canton Amp 5.1: * The (slave) speakers may not be paired to the Amp 5.1. Pair all slave speakers according to chapter Speaker Config [SPC] / Speaker Mapping [SPM]. * The parameter Standby [STB] may be set to ECO [ECO]. If the parameter STB is set to [ECO], each speaker must be switched on separately with the remote control. If you want to switch all speakers on together, set the parameter to NSB, MAN or AUT.
P
Paula HaysSep 8, 2025
Why can't I select an input on my Canton Amp 5.1?
- D
  David WebbSep 8, 2025
  If an input cannot be selected via the input buttons on your Canton Amp 5.1, the input may have been deactivated in the Input Config [INP] menu. Activate the relating input according to chapter Input Config [INP].
D
Dennis StoneSep 1, 2025
How do I manually select Bluetooth input on my Canton Amp 5.1?
- J
  Jennifer Collins DVMSep 2, 2025
  If the input [BT] cannot be selected via the “Input” buttons on your Canton Amp 5.1, it may be because the function BT Select [BTS] is activated. Deactivate the function BT Select [BTS] in order to select the input [BT] manually.
W
William MartinezAug 31, 2025
Canton Amp 5.1 not turning off automatically, how to fix?
- A
  Alexis HarveyAug 31, 2025
  If your Canton Amp 5.1 is not turning off automatically: * The standby function may be set to Manual [MAN]. Activate the standby function ECO, AUT, or NSB. * The standby function Auto [AUT] may be activated, and the source device also transmits a carrier signal in standby mode. Switch off the source device at its mains switch or disconnect it from the mains in any other way.

Canton Smart Amp 5.1 Specifications

General

Video in	3x HDMI
Video out	1x HDMI
Ethernet LAN (RJ-45) ports	1
Speakers connectivity type	-
Product color	Black
Volume control	Touch
Cables included	AC
Treble adjustment	Yes
Connectivity technology	Wired & Wireless
Audio decoders	DTS-HD, Dolby Atmos
Audio output channels	- channels
Peak power per channel	600 W
Signal-to-Noise Ratio (SNR)	- dB
Total Harmonic Distortion (THD)	- %