To Next PageTo Next PageHow to fix Canton Amp 5.1 remote control not working?
If your Canton Amp 5.1 is not responding to the remote control, here are a couple of things to check: 1. Make sure you have removed the protective film on the remote control. 2. The battery may be empty. Replace it, ensuring you use the correct battery type and insert it with the correct polarity.
What to do if Bluetooth playback is interrupted on Canton Amp 5.1?
If you're experiencing no playback or interrupted playback via Bluetooth on your Canton Amp 5.1, consider the following: * Ensure there is a connection between the Amp 5.1 and your mobile device by pairing and connecting them as described in the manual. The mobile device may need to be reconnected. * Increase the volume on both the mobile device (to the maximum possible value) and the Amp 5.1. * Keep sources of interference, such as a WiFi Router or a laptop, away from the Amp 5.1. * If you are using both WiFi and Bluetooth on your mobile device, disable WiFi to prevent potential interference. * Make sure that the distance between the Amp 5.1 and the mobile device is less than 10m.
Why won't my Canton Amp 5.1 turn on?
If your Canton Amp 5.1 is not turning on, ensure that the power cable is correctly connected to both the Amp 5.1 and the power outlet, and that it is fully plugged in.
How to increase volume on Canton Amp 5.1 if it's too soft?
If the sound reproduction on your Canton Amp 5.1 is too soft: * Increase the volume on both the Amp 5.1 and the source device, especially if you're using mobile devices. * Check if the maximum possible volume was limited by the “Volume” function [VOL] and increase it according to the instructions.
Why is my Canton Amp 5.1 speaker buzzing?
If the speaker connected to your Canton Amp 5.1 is buzzing, consider the following: 1. If you are using a signal cable from the source device to the analogue input [AUX] of the Amp 5.1, make sure it is not too long. Use a shorter and/or higher quality (better shielded) signal cable. 2. If the signal cable is not shielded or the shield on the cable is interrupted (defective), replace the cable with a shielded and/or higher quality cable. 3. If there is a ground loop (hum loop) “generated”, connect all devices connected to the Amp 5.1 with a safety plug to a single power strip (multiple socket). 4. If you are operating a non-interference suppressed consumer (e.g. fridge) at the mains, turn off any possible sources of interference for testing purposes.
How to enable auto turn on for Canton Amp 5.1?
If your Canton Amp 5.1 is not turning on automatically: * The standby function may be set to Network [NSB], requiring manual turn-on. To enable automatic turn-on, switch the standby function to Auto [AUT]. * The device may have been switched off via the “ON / Standby” button of the remote control or the “Power” button of the TV remote control. Switch on the Amp 5.1 via the “ON / Standby” button of the remote control and wait until it automatically switches to the standby mode next time. * The signal from the source at the analogue input [AUX] may be too low. Increase the output level (volume) on your analogue source device. * You can delete the “Power” button of your TV remote from the Amp 5.1 to prevent it from switching off together with your TV.
Why does my Canton Amp 5.1 keep turning off?
If your Canton Amp 5.1 is switching off unintentionally: * The standby function may be set to ECO, AUT or NSB. Select the standby function Manual [MAN] if you want the Amp 5.1 to stay on, even without an input signal. * The infrared command for Standby may have been learned incorrectly. Re-learn the infrared command for On (turn on) and Standby (turn off).
Why isn't my WiFi network showing up on my Canton Amp 5.1?
If your WiFi network is not displayed during setup of your Canton Amp 5.1, the network connection may be set to Ethernet [ETH]. Change the setting to WiFi [WIF] in the menu Network Select [NWC].
Why does my Canton Amp 5.1 switch to Bluetooth input by itself?
If your Canton Amp 5.1 is unintentionally switching to the input [BT]: * The function BT Select [BTS] may be activated, and your mobile device is playing system sounds. Deactivate the function BT Select [BTS] and set it back on Manual [MAN]. * Disable all system sounds on your (mobile) device.
How do I manually select Bluetooth input on my Canton Amp 5.1?
If the input [BT] cannot be selected via the “Input” buttons on your Canton Amp 5.1, it may be because the function BT Select [BTS] is activated. Deactivate the function BT Select [BTS] in order to select the input [BT] manually.
General| Video in | 3x HDMI |
|---|---|
| Video out | 1x HDMI |
| Ethernet LAN (RJ-45) ports | 1 |
| Speakers connectivity type | - |
| Product color | Black |
| Volume control | Touch |
| Cables included | AC |
| Treble adjustment | Yes |
| Connectivity technology | Wired & Wireless |
| Audio decoders | DTS-HD, Dolby Atmos |
| Audio output channels | - channels |
| Peak power per channel | 600 W |
| Signal-to-Noise Ratio (SNR) | - dB |
| Total Harmonic Distortion (THD) | - % |
Weight and Dimensions| Depth | 154 mm |
|---|---|
| Width | 245 mm |
| Height | 120 mm |
| Weight | 5240 g |
Essential safety guidelines for device operation, handling, and environment.
Critical warnings regarding electrical hazards, non-opening of the device, and battery risks.
Specific warnings for button cell batteries, including ingestion risks and disposal.
Adjusting individual speaker volume levels using a test tone generator.
Setting speaker distances for optimal spatial effect and sound staging.
Configuring Dynamic Range Control to manage volume differences in audio streams.
Adjusting frequency response for speakers based on room acoustics.
Configuring subwoofer phase, stereo modes, and crossover settings.
Setting crossover frequency for subwoofer and front speakers in 'Xover' mode.
Improving speech intelligibility in dialogues during playback.
Setting crossover frequency between small speakers and the subwoofer.
Adjusting room height for optimal 3D sound impression with Dolby Atmos.
Setting heights for upward-firing speakers to achieve optimal spatial surround.
Setting the automatic shutdown time for the system.
Functions related to infrared remote control operation, including learning codes.
Assigning custom remote control buttons to select specific audio inputs.
Deleting stored IR codes from the amplifier.
Restoring the amplifier to its original factory default settings.
Enabling or disabling HDMI Consumer Electronics Control features.
Resetting all network settings to factory defaults.
Resetting all Bluetooth wireless technology settings and paired devices.
Resetting all stored settings for the wireless audio module and paired speakers.
Establishing wireless connections between the amplifier and smart speakers.
