3
67
English
66
English
Problem Possible cause Solution
An input cannot be
selected via the input
buttons�
The input has been deactivated in the Input Config
[INP] menu (---)�
Activate the relating input according to chapter Input Config
[INP]�
A (slave)speaker shows
[WLS] in the display�
1� The slave speaker is operated without the Amp
5�1�
1� Turn on the Amp 5�1�
2� The (slave-) speaker is not paired anymore� 2� Pair the (slave-) speaker with the Amp 5�1 according
to chapter Speaker Config [SPC] / Speaker Mapping [
SPM]
�
The subwoofer does
not reproduce sound�
1� The Smart subwoofer is not paired, till now� 1� Pair the Smart subwoofer with the Amp 5�1 according
to chapter
Speaker Config [SPC] / Speaker Mapping [
SPM]
2 The subwoofer is connected to the Amp 5�1
using a RCA cable, but Sub Out is set to Off (not
activated)�
2� Activate the output Sub Out at the Output Config [OPC]�
No connection can be
established between
the network router and
the Amp 5�1�
1� The DHCP server is deactivated in the router� 1� Activate the DHCP server of the network router according to
the router's instructions�
2� A filter for MAC addresses was created in the
network router�
2� Deactivate the MAC Address Filter resp� add the adress of the
Amp 5�1�
3� Your router is not compatible with Chromecast
built-in�
3� Routers that are demonstrably compatible can be found in
the web link in the chapter “Using Chromecast built-in”� Howe-
ver, there are more compatible routers�
Your WiFi network is
not displayed during
setup�
1� The network connection for the Amp 5�1 is set to
Ethernet [ETH]�
1� Change the setting to WiFi [WIF] in the menu Network Select
[NWC]�
The Smart Amp 5�1 is not
indicated in the app on
your (mobile) device�
1� Your (mobile) device and the Amp 5�1 must be
conncted to the same network�
1� Connect your (mobile) device resp� the Amp 5�1 to the corres-
ponding network (e�g� when using a guest network)�
Technical Data
Power supply
• Operating voltage 100 – 240V~
• Operating frequency 50 / 60Hz
• Power consumption ECO Standby 0,47 W
• Power consumption NSB Standby WLAN [WIF] ca� 1,94W (Factory setting)
• Power consumption NSB Standby LAN [ETH] ca� 6,8W
• Power consumption AUT Standby ca� 7,1W
• Power consumption MAN Standby ca� 4,5W
• Power consumption Idle (no output signal) ca� 10W
• Power consumption maximum ca� 400W
Signal level
• SUB out = RCA, max� 2,0 V (effective)
• Analog Line [AUX] = RCA, max� 2,0 V (effective)
• Optical [CD] = Toslink, max� 96kHz/24Bit
• Coaxial [DVD] = RCA, max� 96kHz/24Bit
Bluetooth® Technology
• Bluetooth® standard 4�1 (A2DP)
• Distance Up to 10m
• Max� transmission power 100mW (+20dBm)
• Frequency Range 2402–2480MHz (ISM band)
• Antenna Gain 4�2dBi
WLAN
• Max� transmission power 100mW (+20dBm)
• Frequency range 2412–2472MHz (802�11b/g/n)
5150–5350MHz and 5470–5725MHz (802�11a/n/ac)
• Antenna Gain 4�2dBi @ 2�4GHz, 4�5dBi @ 5GHz
Wireless Audio
• Max� transmission power 100mW (+20dBm)
• Frequency Range 2402–2480 MHz (2412MHz, 2438MHz and 2464MHz)
5180–5240 MHz (5180MHz, 5210MHz and 5240MHz)
5736–5814 MHz (5736MHz, 5762MHz and 5814MHz)
• Antenna Gain 4�2dBi @ 2�4GHz, 4�5dBi @ 5GHz
Load Impedance
• Speaker nominal: 4–16 Ω
• Minimum 3 Ω
Dimensions
• W: 24,5 cm
• H: 12,0 cm
• D: 15,4 cm
Weight
• 2,64 kg
Decoder
• Dolby Atmos®
• DTS-HD®
• PCM (32kHz…96kHz, 8Bit…24Bit)
Decoder
• Dolby
®
Surround
Ambient temperature
• Minimum 5 °C (41 °F)
• Maximum 35 °C (95 °F)
To Next Page
Loading...
Need help?
General
Weight and Dimensions
