Canton Smart Amp 5.1 User Manual (English)

Other manuals for Canton Smart Amp 5.1

Manual67 pages

Operating Instructions37 pages

Questions and Answers:

H
Heather TurnerAug 29, 2025
How to enable auto turn on for Canton Amp 5.1?
- N
  Nicole HillAug 29, 2025
  If your Canton Amp 5.1 is not turning on automatically: * The standby function may be set to Network [NSB], requiring manual turn-on. To enable automatic turn-on, switch the standby function to Auto [AUT]. * The device may have been switched off via the “ON / Standby” button of the remote control or the “Power” button of the TV remote control. Switch on the Amp 5.1 via the “ON / Standby” button of the remote control and wait until it automatically switches to the standby mode next time. * The signal from the source at the analogue input [AUX] may be too low. Increase the output level (volume) on your analogue source device. * You can delete the “Power” button of your TV remote from the Amp 5.1 to prevent it from switching off together with your TV.
A
Andrea SolisAug 28, 2025
Why is my Canton Amp 5.1 speaker buzzing?
- D
  Deborah MooreAug 28, 2025
  If the speaker connected to your Canton Amp 5.1 is buzzing, consider the following: 1. If you are using a signal cable from the source device to the analogue input [AUX] of the Amp 5.1, make sure it is not too long. Use a shorter and/or higher quality (better shielded) signal cable. 2. If the signal cable is not shielded or the shield on the cable is interrupted (defective), replace the cable with a shielded and/or higher quality cable. 3. If there is a ground loop (hum loop) “generated”, connect all devices connected to the Amp 5.1 with a safety plug to a single power strip (multiple socket). 4. If you are operating a non-interference suppressed consumer (e.g. fridge) at the mains, turn off any possible sources of interference for testing purposes.
D
David GrahamAug 27, 2025
How to increase volume on Canton Amp 5.1 if it's too soft?
- S
  Susan DuncanAug 28, 2025
  If the sound reproduction on your Canton Amp 5.1 is too soft: * Increase the volume on both the Amp 5.1 and the source device, especially if you're using mobile devices. * Check if the maximum possible volume was limited by the “Volume” function [VOL] and increase it according to the instructions.
F
Frederick GordonAug 27, 2025
Why won't my Canton Amp 5.1 turn on?
- T
  Tracy GuzmanAug 27, 2025
  If your Canton Amp 5.1 is not turning on, ensure that the power cable is correctly connected to both the Amp 5.1 and the power outlet, and that it is fully plugged in.
N
Nancy White MDAug 26, 2025
What to do if Bluetooth playback is interrupted on Canton Amp 5.1?
- W
  William LaraAug 27, 2025
  If you're experiencing no playback or interrupted playback via Bluetooth on your Canton Amp 5.1, consider the following: * Ensure there is a connection between the Amp 5.1 and your mobile device by pairing and connecting them as described in the manual. The mobile device may need to be reconnected. * Increase the volume on both the mobile device (to the maximum possible value) and the Amp 5.1. * Keep sources of interference, such as a WiFi Router or a laptop, away from the Amp 5.1. * If you are using both WiFi and Bluetooth on your mobile device, disable WiFi to prevent potential interference. * Make sure that the distance between the Amp 5.1 and the mobile device is less than 10m.
D
Danielle WilliamsAug 25, 2025
How to fix Canton Amp 5.1 remote control not working?
- A
  Angel SmithAug 26, 2025
  If your Canton Amp 5.1 is not responding to the remote control, here are a couple of things to check: 1. Make sure you have removed the protective film on the remote control. 2. The battery may be empty. Replace it, ensuring you use the correct battery type and insert it with the correct polarity.
T
Terry SheppardAug 25, 2025
Why is there no sound coming from my Canton Amp 5.1?
- V
  Valerie RitterAug 25, 2025
  If there is no sound from your Canton Amp 5.1, there might be several reasons: * The sound format selected on your source device may be incorrect; please check its settings. * There may be no signal from the player, or the volume is set to "zero"; unlock the digital output on the source device and increase the volume. * The cable may not be connected correctly or is defective; check the connection between the player and the Amp 5.1, and replace the cable if necessary. * Ensure that the protective caps on the connectors of the optical cable (TOSLINK) are removed.

Canton Smart Amp 5.1 Specifications

General

Video in	3x HDMI
Video out	1x HDMI
Ethernet LAN (RJ-45) ports	1
Speakers connectivity type	-
Product color	Black
Volume control	Touch
Cables included	AC
Treble adjustment	Yes
Connectivity technology	Wired & Wireless
Audio decoders	DTS-HD, Dolby Atmos
Audio output channels	- channels
Peak power per channel	600 W
Signal-to-Noise Ratio (SNR)	- dB
Total Harmonic Distortion (THD)	- %

Weight and Dimensions

Depth	154 mm
Width	245 mm
Height	120 mm
Weight	5240 g

Related product manuals

Canton Smart Connect 5.1

70 pages

Canton Smart Amp 5.1 Short Manual

Table of Contents

Other manuals for Canton Smart Amp 5.1

Questions and Answers:

Canton Smart Amp 5.1 Specifications

Related product manuals