Instruction manual DD810BK
35
Please keep this instruction manual for future reference
STOP DELAY TIME:
The fan motor should continue operating for another 10-20 minutes every time the hob has been
used for cooking. When the fan is switched off after having been in operation for at least 15
minutes, an automatic time lag at a low setting will follow for around 15 minutes.
This guarantees optimal functioning and the removal of remaining cooking steam. When using
a recirculating air filter, please always allow for a stop delay time of 10 - 60 minutes in order to
optimally remove cooking odours.
When the fan is switched on again, in rare cases the odour molecules present in the filter may
be combined with steam so that they are detected again. These remaining odours will disappear
when the fan continues to operate.
IMPORTANT:
When the convection air mode is in operation, ventilation must be sufficient in order for the air
humidity to be removed.
REPLACEMENT OF THE FILTER :
If an existing carbon filter must be cleaned or replaced, this is indicated in the fan display by a
.
S TOP DELAY TIME:
The fan motor should continue operating for another 10-20 minutes every time the hob has been
used for cooking. When the fan is switched offffafter having been in operation for at least 15
minutes, an automatic time lag at a low setting will follow for around 15 minutes.
This guarantees optimal functioning and the removal of remaining cooking steam.
When using a recirculating air filter, please always allow for a stop delay time of 10 - 60 minutes
in order to optimally remove cooking odours.
When the fan is switched on again, in rare cases the odour molecules present in the filter may
be combined with steam so that they are detected again. These remaining odours will disappear
when the fan continues to operate.
I MPORTANT:
When the convection air mode is in operation, ventilation must be sufficient in order for the air
humidity to be removed.
R E PLACEMENT OF THE FILTER:
If an existing carbon filter must be cleaned or replaced, this is indicated in the fan display by a
When the fan is switched on, the display for a cooking process is deleted.
must be pressed To reset the display, the fan display and the touch control
simultaneously for approx. 3 seconds.
If no carbon filter is used, the display indication must also be reset.
.
When the fan is switched on, the display for a cooking process is deleted.
To reset the display, the fan display and the touch control
.
S TOP DELAY TIME:
The fan motor should continue operating for another 10-20 minutes every time the hob has been
used for cooking. When the fan is switched offffafter having been in operation for at least 15
minutes, an automatic time lag at a low setting will follow for around 15 minutes.
This guarantees optimal functioning and the removal of remaining cooking steam.
When using a recirculating air filter, please always allow for a stop delay time of 10 - 60 minutes
in order to optimally remove cooking odours.
When the fan is switched on again, in rare cases the odour molecules present in the filter may
be combined with steam so that they are detected again. These remaining odours will disappear
when the fan continues to operate.
I MPORTANT:
When the convection air mode is in operation, ventilation must be sufficient in order for the air
humidity to be removed.
R E PLACEMENT OF THE FILTER:
If an existing carbon filter must be cleaned or replaced, this is indicated in the fan display by a
When the fan is switched on, the display for a cooking process is deleted.
must be pressed To reset the display, the fan display and the touch control
simultaneously for approx. 3 seconds.
If no carbon filter is used, the display indication must also be reset.
must be pressed
simultaneously for approx. 3 seconds.
If no carbon filter is used, the display indication
.
S TOP DELAY TIME:
The fan motor should continue operating for another 10-20 minutes every time the hob has been
used for cooking. When the fan is switched offffafter having been in operation for at least 15
minutes, an automatic time lag at a low setting will follow for around 15 minutes.
This guarantees optimal functioning and the removal of remaining cooking steam.
When using a recirculating air filter, please always allow for a stop delay time of 10 - 60 minutes
in order to optimally remove cooking odours.
When the fan is switched on again, in rare cases the odour molecules present in the filter may
be combined with steam so that they are detected again. These remaining odours will disappear
when the fan continues to operate.
I MPORTANT:
When the convection air mode is in operation, ventilation must be sufficient in order for the air
humidity to be removed.
R E PLACEMENT OF THE FILTER:
If an existing carbon filter must be cleaned or replaced, this is indicated in the fan display by a
When the fan is switched on, the display for a cooking process is deleted.
must be pressed To reset the display, the fan display and the touch control
simultaneously for approx. 3 seconds.
If no carbon filter is used, the display indication must also be reset.
must also be reset.
To Next Page
Loading...
