Cardinal 2-OU Series - User Manual

Questions and Answers

D
dcochranAug 20, 2025
What to do if Cardinal 2-OU Accessories display shows oCAP (over Capacity)?
- A
  adam98Aug 20, 2025
  If the Cardinal Accessories display shows 'oCAP', it means the load on the scale exceeds the scale capacity plus nine divisions. You should remove the excess load from the scale platform. This may also indicate miscalibration.
C
Cheryl WilliamsAug 22, 2025
What does ErrAh (Error Analog high) mean on Cardinal Accessories, and how to fix it?
- R
  Rhonda MartinezAug 22, 2025
  If you see 'ErrAh' on your Cardinal Accessories, it indicates that the load cell input is above the range of the indicator. Check for improper load cell wiring, excessive load, and ensure the output is between 1 to 40mV. If the issue persists, it may be due to load cell or circuit failure.
L
Leslie PerryAug 25, 2025
What does ErrAL (Error Analog Low) mean on Cardinal 2-OU Accessories, and how do I resolve it?
- J
  Jordan LeeAug 25, 2025
  If your Cardinal Accessories display shows 'ErrAL', it means the load cell input is below the range of the indicator. Check for improper load cell wiring and ensure the output is between 1 to 40mV. If the issue continues, it could be a load cell or circuit failure.
D
drew04Aug 26, 2025
How to resolve incorrect weight displayed on Cardinal 2-OU Accessories?
- D
  Donna HughesAug 27, 2025
  If your Cardinal Accessories are displaying an incorrect weight, ensure the indicator has been calibrated. Also, check that the scale platform isn't touching any adjacent objects and inspect the load cell connector wiring. If you're using four-wire load cells, make sure the sense lead jumpers (J6 & J9) are installed. Finally, verify that proper operating procedures have been followed.
L
Luke MendozaAug 27, 2025
What does '-oF- (overflow)' mean on Cardinal 2-OU and how can I fix it?
- H
  Hannah MooreAug 28, 2025
  If your Cardinal Accessories displays '-oF-', it means the indicator is attempting to display a positive number greater than six digits in length or a negative number of more than five digits. Return to Gross Weight mode and review the Tare value. This issue may also indicate miscalibration.
J
Juan SalinasAug 30, 2025
How to fix UnStb (Unstable) message on Cardinal Accessories?
- A
  alexanderrodneyAug 30, 2025
  If your Cardinal Accessories displays 'UnStb', it means there's motion present when trying to perform a print function. Wait for a stable weight display, indicated by the 'STABLE' annunciator being on, before proceeding.
A
Amy CastilloAug 31, 2025
How to resolve E[2]PROM checksum failure in Cardinal 2-OU Accessories?
- J
  Joseph PalmerSep 1, 2025
  If you encounter an 'E[2]PROM checksum failure' message on your Cardinal Accessories, recalibrate the device using a calibrated test weight.
W
wcastilloSep 2, 2025
What does EEFAiL (External EEPROM memory write/read failure) mean for Cardinal 2-OU?
- M
  Marcus HernandezSep 2, 2025
  If your Cardinal Accessories displays 'EEFAiL', it indicates an external EEPROM memory write/read failure. Press any key to continue. No other action is necessary if ID storage is not used.
R
Robin ButlerSep 4, 2025
What does EE Err (External EEPROM memory retention error) mean on Cardinal 2-OU Accessories?
- L
  Linda GarnerSep 4, 2025
  If your Cardinal Accessories displays 'EE Err', it indicates an external EEPROM memory retention error. Press any key to continue. No other action is necessary if ID storage is not used.
K
karen94Sep 6, 2025
What does iiCErr (IIC bus failure) mean on Cardinal Accessories?
- P
  Patricia LozanoSep 6, 2025
  If your Cardinal Accessories displays 'iiCErr', it indicates an IIC bus failure. Press any key to continue.