Need help?Do you have a question about the CareFusion Infant Flow LP SiPAP and is the answer not in the manual?
Outlines restrictions and exclusions to the product warranty coverage.
Instructions for connecting the Infant Flow LP SiPAP system and patient circuit.
Procedure for powering on the Infant Flow LP SiPAP driver unit.
Steps to ensure the Infant Flow LP SiPAP system is operating correctly.
Procedures for calibrating system sensors and parameters.
How to operate the IFSD when AC or battery power is unavailable.
Information on how the unit indicates faults and errors.
Accessing diagnostic screens for testing and error logging.
Information regarding electromagnetic compatibility of the equipment.
Warnings about operating the device in MRI environments.
Details on the expanded capabilities and features of the Infant Flow systems.
Overview of the different operating modes available for the system.
Description of the system's user-adjustable controls and parameters.
List of parameters monitored by the Infant Flow LP SiPAP system.
Definitions for WARNINGS, CAUTIONS, and NOTES used in the manual.
Critical safety warnings for operating the Infant Flow LP SiPAP system.
Explanation of how gas flows through the Infant Flow LP SiPAP system.
Steps for setting up and connecting the Infant Flow LP SiPAP system.
Automatic test performed on unit power-up to verify functionality.
Indication and action for low battery voltage.
System response to critical software faults preventing operation.
How the system indicates and responds to over-pressure conditions.
Required initial settings for performing alarm verification tests.
Recommended schedule for preventative maintenance services.
Steps involved in the preventative maintenance process.
List of tools needed for maintenance procedures.
Procedure for removing the outer case of the IFSD.
Procedure for refitting the outer case of the IFSD.
Steps for removing the internal battery from the IFSD.
Steps for installing a new internal battery into the IFSD.
Procedure for removing the oxygen filter component.
Procedure for installing a new oxygen filter component.
Procedure for removing the fuel cell filter/restrictor.
Procedure for installing the fuel cell filter/restrictor.
Steps for removing the oxygen sensor from the flow mixer block.
Steps for installing a new oxygen sensor.
Procedure for removing the blender and associated components.
Procedure for removing the water trap filter.
Procedure for installing a new water trap filter.
Steps to remove pilot drive check valves from the flowmeters.
Steps to install pilot drive check valves onto the flowmeters.
Procedure to remove the case bleed filtered restrictor.
Procedure to install the case bleed filtered restrictor.
Steps for removing the valve/sensor PCB.
Steps for installing the valve/sensor PCB.
Procedure for removing the muffler/filter.
Procedure for installing the muffler/filter.
Technical parameter ranges for non-US configurations of the system.
Technical parameter ranges for US configurations of the system.
Default values for key operational parameters of the system.
Outlines restrictions and exclusions to the product warranty coverage.
Instructions for connecting the Infant Flow LP SiPAP system and patient circuit.
Procedure for powering on the Infant Flow LP SiPAP driver unit.
Steps to ensure the Infant Flow LP SiPAP system is operating correctly.
Procedures for calibrating system sensors and parameters.
How to operate the IFSD when AC or battery power is unavailable.
Information on how the unit indicates faults and errors.
Accessing diagnostic screens for testing and error logging.
Information regarding electromagnetic compatibility of the equipment.
Warnings about operating the device in MRI environments.
Details on the expanded capabilities and features of the Infant Flow systems.
Overview of the different operating modes available for the system.
Description of the system's user-adjustable controls and parameters.
List of parameters monitored by the Infant Flow LP SiPAP system.
Definitions for WARNINGS, CAUTIONS, and NOTES used in the manual.
Critical safety warnings for operating the Infant Flow LP SiPAP system.
Explanation of how gas flows through the Infant Flow LP SiPAP system.
Steps for setting up and connecting the Infant Flow LP SiPAP system.
Automatic test performed on unit power-up to verify functionality.
Indication and action for low battery voltage.
System response to critical software faults preventing operation.
How the system indicates and responds to over-pressure conditions.
Required initial settings for performing alarm verification tests.
Recommended schedule for preventative maintenance services.
Steps involved in the preventative maintenance process.
List of tools needed for maintenance procedures.
Procedure for removing the outer case of the IFSD.
Procedure for refitting the outer case of the IFSD.
Steps for removing the internal battery from the IFSD.
Steps for installing a new internal battery into the IFSD.
Procedure for removing the oxygen filter component.
Procedure for installing a new oxygen filter component.
Procedure for removing the fuel cell filter/restrictor.
Procedure for installing the fuel cell filter/restrictor.
Steps for removing the oxygen sensor from the flow mixer block.
Steps for installing a new oxygen sensor.
Procedure for removing the blender and associated components.
Procedure for removing the water trap filter.
Procedure for installing a new water trap filter.
Steps to remove pilot drive check valves from the flowmeters.
Steps to install pilot drive check valves onto the flowmeters.
Procedure to remove the case bleed filtered restrictor.
Procedure to install the case bleed filtered restrictor.
Steps for removing the valve/sensor PCB.
Steps for installing the valve/sensor PCB.
Procedure for removing the muffler/filter.
Procedure for installing the muffler/filter.
Technical parameter ranges for non-US configurations of the system.
Technical parameter ranges for US configurations of the system.
Default values for key operational parameters of the system.
General| Category | Medical Equipment |
|---|---|
| Brand | CareFusion |
| Model | Infant Flow LP SiPAP |
| Patient Population | Neonates and infants |
| FiO2 Range | 21-100% |
| Intended Use | Non-invasive respiratory support for neonates and infants |
| Mode of Ventilation | CPAP |
| Flow Range | Up to 20 L/min |
| Humidification | Integrated humidification system |
| Display | LCD screen |
| Power Supply | AC power supply |
| Compliance | Meets relevant medical standards (e.g., IEC 60601-1) |
| Dimensions | 30 cm x 20 cm x 15 cm |
| Weight | 5 kg |
| Trigger | Flow trigger |
To Next Page