1111053901
Confirmation of Indoor Unit Setup
Prior to delivery to the customer, check the address and setup of the indoor unit, which has been installed
in this time and fill the check sheet (Table below). Data of four units can be entered in this check sheet.
Copy this sheet according to the No. of the indoor units. If the installed system is a group control system,
use this sheet by entering each line system into each installation manual attached to the other indoor units.
REQUIREMENT
This check sheet is required for maintenance after installation. Fill this sheet and then pass this Installation
Manual to the customers.
Indoor unit setup check sheet
Indoor unit Indoor unit Indoor unit Indoor unit
Room name Room name Room name Room name
Model Model Model Model
Check indoor unit address. (For check method, refer to Applicable controls in this manual.)
* In case of a single system, it is unnecessary to enter the indoor address. (CODE No.: Line [12], Indoor [13], Group [14], Central control
[03])
Line Indoor Group Line Indoor Group Line Indoor Group Line Indoor Group
Central control address Central control address Central control address Central control address
Various setup Various setup Various setup Various setup
Have you changed lighting time of filter sign? If not, fill check mark [×] in [NO CHANGE], and fill check mark [×] in [ITEM] if changed,
respectively.
(For check method, refer to Applicable controls in this manual.)
Filter sign lighting time
(CODE No. [01])
NO CHANGE
NONE [0000]
150H [0001]
2500H [0002]
5000H [0003]
10000H [0004]
Filter sign lighting time
(CODE No. [01])
NO CHANGE
NONE [0000]
150H [0001]
2500H [0002]
5000H [0003]
10000H [0004]
Filter sign lighting time
(CODE No. [01])
NO CHANGE
NONE [0000]
150H [0001]
2500H [0002]
5000H [0003]
10000H [0004]
Filter sign lighting time
(CODE No. [01])
NO CHANGE
NONE [0000]
150H [0001]
2500H [0002]
5000H [0003]
10000H [0004]
Have you changed detected temp. shift value? If not, fill check mark [×] in [NO CHANGE], and fill check mark [×] in [ITEM] if changed,
respectively.
(For check method, refer to Applicable control in this manual.)
Detected temp. shift value setup
(CODE No. [06])
NO CHANGE
NO SHIFT [0000]
+1°C 1.8°F [0001]
+2°C 3.6°F [0002]
+3°C 5.4°F [0003]
+4°C 7.2°F [0004]
+5°C 9.0°F [0005]
+6°C 10.8°F [0006]
Detected temp. shift value setup
(CODE No. [06])
NO CHANGE
NO SHIFT [0000]
+1°C 1.8°F [0001]
+2°C 3.6°F [0002]
+3°C 5.4°F [0003]
+4°C 7.2°F [0004]
+5°C 9.0°F [0005]
+6°C 10.8°F [0006]
Detected temp. shift value setup
(CODE No. [06])
NO CHANGE
NO SHIFT [0000]
+1°C 1.8°F [0001]
+2°C 3.6°F [0002]
+3°C 5.4°F [0003]
+4°C 7.2°F [0004]
+5°C 9.0°F [0005]
+6°C 10.8°F [0006]
Detected temp. shift value setup
(CODE No. [06])
NO CHANGE
NO SHIFT [0000]
+1°C 1.8°F [0001]
+2°C 3.6°F [0002]
+3°C 5.4°F [0003]
+4°C 7.2°F [0004]
+5°C 9.0°F [0005]
+6°C 10.8°F [0006]
Incorporation of parts sold
separately
Incorporation of parts sold
separately
Incorporation of parts sold
separately
Incorporation of parts sold
separately
Have you incorporated the following parts sold separately? If incorporated, fill check mark [×] in each [ITEM].
(When incorporating, the setup change is necessary in some cases. For setup change method, refer to Installation Manual attached to
each part sold separately.)
Others ( )
Others ( )
Others ( )
Others ( )
Others ( )
Others ( )
Others ( )
Others ( )
+001111053901_00Ta.book Page 33 Monday, January 17, 2011 11:35 AM
To Previous Page
Loading...
Need help?
General
