Carrier RG66B3/BGEF - DRY Operation (Dehumidifying); FAN Operation

13 14
The Follow me function enables the
remote control to measure the temperature
at its current location and
.
When using AUTO, COOL, or HEAT modes,
measuring ambient temperature from the
remote control (instead of from the indoor
unit itself) will enable the air conditioner to
optimize the temperature around you and
ensure maximum comfort.
send this signal
to the air conditioner every 3 minutes interval
FOLLOW ME function
ECO function
Silence function
SLEEP Function
O
8 C Heating Function
The SLEEP function is used to decrease
energy use while you sleep (and don t
need the same temperature settings to
stay comfortable). This function can
only be activated via remote control.
Note:
in
MODE, FAN, TURBO, SELF CLEAN or
ECO button will stop sleep operation.
The SLEEP function is not available
FAN or DRY mode. Press ON/OFF,
,
How To Use The Advanced Functions How To Use The Advanced Functions
The TURBO function makes the unit work
extra hard to reach your present temperature
in the shortest amount of time possible.
When you select TURBO feature in COOL
mode, the unit will blow cool air with
strongest wind setting to jump-start the
cooling process.
When you select TURBO feature in HEAT
mode, for units with Electric heat elements,
the Electric Heater will activate and
jump-start the heating process.
TURBO function(TURBO/FRESH) function
For the detail, see sleep operation in
USER S MANUAL.
,
,,
,,
,,
,,
NOTE: This function is only available under
COOL mode.
Hold down Fan speed button for 2 seconds
to activate/cancel Silent mode. Due to low
frequency operation of compressor, it may
result in insufficient cooling and heating
capacity. (applicable to the air conditioner
with Silent feature only)
Mode
Mode
Fan
Fan
ON/OFF
ON/OFF
When the air conditioner operates under
heating mode with the set temperature
O
of 16 C, press Temp button twice in
one second will activate 8 Degree heating
function. The unit will operate at a setting
O
temperature of 8 C. The indoor unit
display shows FP . For some units,
O
press this button can activate 12 C
heating feature, please refer to the
Owner s Manual of the air conditioner.
,,
,,
Used to enter the energy efficient mode.
Under cooling mode, press this button,
the remote controller will adjust the
O
temperature automatically to 24 C, fan
speed of Auto to save energy(but only
O
if the set temperature is less than 24 C).
O
If the set temperature is above 24 C ,
press the ECO button, the fan speed
will change to Auto, the set temperature
will remain unchanged.
NOTE:
Pressing the ECO button, or modifying
the mode or adjusting the set temperature
O
to less than 24 C will stop ECO operation.
Under ECO operation, the set temper-
O
ature should be 24 C or more. it may
result in insufficient cooling. If you feel
uncomfortable, just press the ECO
button again to stop it.
Airborne bacteria can grow in the moisture
that condenses around heat exchanger in
the unit. With regular use, most of this
moisture is evaporated from the unit.
When the Self clean feature is activated,
your unit will clean itself automatically. After
cleaning the unit will turn off automatically.
You can use Self clean feature as often as
you like.
Note: You can only activate this function
in COOL or DRY mode.
Note: The Intelligent eye function will stop if
you press the other buttons except Timer and
LED buttons.
SELF CLEAN function
NOTE: Press and hold Temp and
buttons together for 3 seconds will
alternate the temperature display
O O
between the C & F scale.
LOCK function
Press Turbo button and Self clean
button simultaneously for one second
to lock or unlock the keyboard.
Hold together for one
second to activate
LOCK function
Hold down Fan
button for 2
seconds to activate
Silence function
Press this button
twice in one second
O
to activate 8 C
heating function
TimerTimer
LED
Self
clean
Turbo
TimerTimer
LED
Turbo
Self
clean
Follow
me
INTELLIGENT EYE function
Press the button to activate wind flow
follow people feature, the fan speed is Auto,
and the auto swing feature is activated.
Press it again to stop and activate the wind
flow away people feature. The fan speed is
Auto, and the auto swing feature is turned off.
Press it the third time to stop the wind flow
away people feature.
Follow
me
,,
,,
,
Hold down Eco
button for 2 seconds
to activate/cancel
SLEEP function.
Hold down Turbo/Fresh button for 2 seconds,
the Fresh feature will be activated. The
Ionizer/Plasma Dust Collector(depending on
models) is energized and will help to remove
pollen and impurities from the air (For model
RG66B4(2H)/BGEF only).