Carrier WeatherMaker 48TCD/E09 Series - Page 58

60 pages

To Next Page

To Previous Page

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.

Catalog No. 04-53480257-01 Printed in U.S.A. Form 48TC-7-16-02SI Pg 58 5-2020 Replaces: 48TC-7-16-01SI

Main Page

Default Chapter1
- Table of Contents1
Safety Considerations2
General3
Rated Indoor Airflow (Cfm)3
Pre-Installation3
Installation16
Step 1 - Plan for Unit Location16
- Roof Mount16
Step 2 - Plan for Sequence of Unit Installation17
- Curb-Mounted Installation17
- Pad-Mounted Installation17
- Frame-Mounted Installation17
Step 3 - Inspect Unit17
Step 4 - Provide Unit Support17
- Roof Curb Mount17
- For Sizes 07-14 Only17
- Slab Mount (Horizontal Units Only)21
- Alternate Unit Support21
- Slab Mount)21
Step 5 - Field Fabricate Ductwork21
Step 6 - Rig and Place Unit21
- Positioning on Curb22
Step 7 - Convert to Horizontal and Connect23
- Ductwork (When Required)23
- Sizes23
- Size 1624
- All Units24
Step 8 - Install Outside Air Hood24
- Economizer and Two-Position Damper Hood24
- Package Removal (Factory Option Sizes 07-14)24
- Two-Position Damper Hood Removal (Factory Option Size 16)25
- Economizer and Two-Position Damper Hood25
- Setup (Size 16)25
Step 9 - Install Flue Hood26
Step 10 - Install Gas Piping26
- Factory-Option Thru-Base Connections (Gas Connections) (Sizes 07-14)27
- Factory-Option Thru-Base Gas Connections (Size 16)28
- All Units29
Step 11 - Install External Condensate Trap and30
- Line30
Step 12 - Make Electrical Connections30
- Field Power Supply (Sizes 07-14)30
- Field Power Supply (Size 16)31
- All Units32
- Units with Factory-Installed Non-Fused Disconnect32
- Units Without Factory-Installed Non-Fused Disconnect33
- All Units33
- Convenience Outlets34
- All Units35
- Factory-Option Thru-Base Connections (Electrical Connections) (Size 07-14)35
- Factory-Option Thru-Base Connections (Electrical Connections) (Size 16)36
- Humidi-Mizer® Control Connections38
Economi$Er® X (Factory-Installed Option)41
- Product Description41
- System Components41
- Specifications41
- Inputs42
- Outputs42
- Environmental42
- Economizer Module Wiring Details42
- S-Bus Sensor Wiring43
- Interface Overview44
- User Interface44
- Keypad44
- Menu Structure44
- Setup and Configuration44
- Time-Out and Screensaver44
- Enthalpy Settings52
- Two-Speed Fan Operation52
- Checkout53
- Troubleshooting53
Premierlink™ Control54
RTU Open Control System54
- Smoke Detectors54
- Completing Installation of Return-Air Smoke Sensor54
- Additional Application Data54
Step 14 - Install Accessories55
Step 15 - Check Belt Tension55
- Belt Force - Deflection Method55
- Belt Tension Method56
Step 13 - Adjust Factory-Installed Options55
- Smoke Detectors55
- Economi$Er IV Occupancy Switch55
Pre-Start and Start-Up56
Troubleshooting the Ultra Tech™ Compressor56
- Modulation Control Input Specifications56
Start-Up Checklist59

Carrier WeatherMaker 48TCD/E09 Series - Page 58

Table of Contents

Related product manuals