Cateye Strada Slim CC-RD310W - User Manual

STRADA SLIM
CC-RD310W
ENG 1
Before using the computer, please thoroughly read this manual and keep
it for future reference.
Please visit our website, where detailed instructions with movies are
available and the instruction manual can be downloaded.
Warning / Caution
•Do not concentrate on the computer while riding. Ride safely!
•Install the magnet, sensor, and bracket securely. Check these periodically.
•If a child swallows a battery, consult a doctor immediately.
•Do not leave the computer in direct sunlight for a long period of time.
•Do not disassemble the computer.
•Do not drop the computer to avoid malfunction or damage.
•When you press the MODE button with the computer installed to the bracket, press around the
dot section on the surface of the computer. Pressing strongly the other section may result in
malfunction or damage.
•When cleaning the computer, bracket and sensor, do not use thinners, benzene, or alcohol.
•Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to local regulations.
•LCD screen may be distorted when viewed through polarized sunglass lenses.
Wireless Sensor
The sensor was designed to receive signals within a maximum range of 60 cm, to reduce
chance of interference.
When adjusting the wireless sensor, note the following:
•Signals cannot be received if the distance between the sensor and the computer is too large.
•The receiving distance may be shortened due to low temperature and exhausted batteries.
•Signals can be received only when the back of the computer is facing the sensor.
Interference may occur, resulting in incorrect data, if the computer is:
•Near a TV, PC, radio, motor, or in a car or train.
•Close to a railroad crossing, railway tracks, TV stations and/or radar base.
•Using with other wireless devices, or some particular battery lights.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:(1)This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device
that are not expressly approved by CatEye Co., Ltd. May void the user ’s authority to operate
the equipment.
Hereby, CATEYE Co., Ltd., declares that this CC-RD310W is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
This model comes with a sensor inspired by modern road bikes.
It may not be used for bikes with a large space between the front fork and
spoke.
CATEYE
STRADA SLIM
CYCLOCOMPUTER
CC-RD310W

Summary

Preparing the Computer

Clear all data (initialization)

Resets the computer to factory settings before first use or after updates.

Select speed units

Choose between kilometers per hour (km/h) or miles per hour (mph) for speed display.

Enter tire circumference

Input front wheel circumference for accurate speed and distance calculations.

Set the clock

Configure the device's time, including display format, hour, and minute.

Tire circumference reference

Reference table for determining and inputting tire circumference values.

Installing the Unit on Your Bicycle

Bracket mounting options

Guidance on attaching the bracket to the bicycle's stem or handlebar.

Mounting bracket to the stem

Step-by-step instructions for securing the bracket onto the bicycle stem.

Mounting bracket to the handlebar

Step-by-step instructions for securing the bracket onto the bicycle handlebar.

Sensor and Magnet Installation

Installation conditions

Ensuring optimal sensor and magnet placement for signal reception.

Install the speed sensor

Procedure for attaching the speed sensor to the bicycle fork.

Install the magnet

Procedure for attaching the magnet to a bicycle spoke.

Computer mounting and testing

Final steps for attaching the computer and verifying sensor operation.

Operating the Computer

Measuring screen overview

Explanation of icons, pace arrow, and speed unit displayed on the measuring screen.

MODE button operation

How to use the MODE button when the computer is attached to the bracket.

Switching displayed data

Cycling through different data modes like Elapsed Time, Trip Distance, and Total Distance.

Computer Operation Modes

Starting and stopping measurement

Automatic measurement based on bicycle movement and speed unit flashing.

Data reset procedures

How to reset specific data like trip distance (Dst2) or all data except total distance.

Power-saving features

Automatic display of clock after inactivity, and screen changes to save power.

Changing Computer Settings

Menu screen navigation

Overview of how to access and navigate through various setting menus.

Tire circumference settings

Selecting between two tire circumference profiles (A/B) and setting the value.

Measurement unit and clock settings

Configuring speed units (km/h/mph) and the device's time display.

Total distance and function settings

Entering cumulative distance and customizing displayed data functions.

Detailed Settings Configuration

Setting the clock display

Adjusting the clock format (12h/24h) and setting the hour and minute.

Setting the function display

Customizing which data fields are displayed by skipping unwanted ones.

Advanced Settings

Entering total distance

Manually inputting the total distance, useful after battery replacement.

Selecting measurement unit

Choosing between km/h and mph as the primary speed measurement unit.

Maintenance and Troubleshooting

Cleaning the computer

Instructions for cleaning the device and accessories with a soft cloth.

Replacing the computer battery

Procedure for replacing the CR1616 battery in the computer unit.

Replacing the speed sensor battery

Procedure for replacing the CR2032 battery in the speed sensor.

Troubleshooting sensor signal

Diagnosing issues when the sensor signal icon does not flash.

Troubleshooting no button response

Resolving issues where no display appears upon pressing a button.

Specifications and Warranty

Computer and sensor specifications

Technical details including battery life, transmission distance, and dimensions.

Limited warranty information

Details on the two-year warranty for the computer and sensor.

Contact information

Customer service contact details for CatEye in Japan and the USA.

Cateye Strada Slim CC-RD310W Specifications

General

Model	CC-RD310W
Display	LCD
Functions	Current Speed, Total Distance, Trip Distance, Elapsed Time, Average Speed, Maximum Speed, Clock
Wireless	Yes
Waterproof	Yes
Battery	CR2032
Mount Type	Handlebar or Stem
Current Speed	Yes
Total Distance	Yes
Trip Distance	Yes
Elapsed Time	Yes
Average Speed	Yes
Maximum Speed	Yes
Clock	Yes
Category	Bicycle Computer
Battery Life	Approx. 1 year