CEM MARS Series - User Manual

• Determine the line voltage from outlet:
60 Hz - 208 V or 230 V
50 Hz - 200 V, 220 V or 240 V
• Select the line voltage.
• Restart system.
10
• Go to www.cem.com/register to
register your system.
• See back of this sheet for details.
12
• After restart, select “Settings”, then
“Video”, then “Welcome” for a short
introduction. (Not available on all
systems)
11
• Remove the box from inside of the
system cavity.
• Write down the serial number located
on the back left side of the system.
7
• Lay the sides of the box at.
• Remove the foam from the top of
the system.
4
• Pull plastic tab, swing handle open.
• Remove plastic assembly from box.
• Repeat process on other 3
assemblies.
1
• Push the power button on the side of
the system to turn it on.
9
• Remove the plastic and discard.
Do not leave the plastic under
the system.
6
• Carefully cut the tape on both sides
of the inner box.
3
• Attach the exhaust hose, and connect
to back of the system.
• Plug power cord into the system and
a dedicated, grounded outlet.
8
• Lift the system, from the sides, onto
bench top near exhaust service (two
people required). Do not place the
system in a fume hood.
5
• Use top handles to pull up and
remove outer box.
2
Installation Location
1. Designate an area with a sturdy work-
bench within 8' (2.5 m) of a hood or
suitable fume disposal mechanism.
2. Provide at least 8" (20.3 cm) space
on each side and 3" (7.6 cm) space
in the rear for ventilation.
System Dimensions:
21" (53.3 cm) W x 25" (63.5 cm) D x
25" (63.5) H
140 lb in weight (without vessels)
3. Allow space for sample handling
4. The system must be free from the
vibration of large equipment or
walk-through trafc
5. The system must be away from the
primary exits and walk-through trafc
6. Location should have a temperature
of 41°F (5 °C) – 104 °F (40 °C).
7. The system should be connected to
a dedicated, grounded outlet.
Ventilation Requirements
The system comes with 8' (2.5 m) of
exible exhaust hose (3
1
∕8" OD x 2
13
∕16"
ID). The built-in exhaust system will push
fumes through the hose at 125 CFM.
To properly vent the system, your hood
or exhaust line must draw at least 125
CFM at the point of connection.
Electrical Requirements
The MARS unit requires 208/230 V, 60
Hz, 15A @ 230 V, or 200/220/240 V, 50
Hz, 15A @ 240 V, single phase power. It
requires a 250 V 15 A rated receptacle
(NEMA 6-15R) or a 250 V - 20 A rated re-
ceptacle (NEMA 6-20R). It is non-locking.
MARS Series
Installation Guide

CEM MARS Series Specifications

General

Brand	CEM
Model	MARS Series
Category	Laboratory Equipment
Language	English

Summary

Installation Location Requirements

Work Area Designation

Designate a sturdy workbench within 8 ft (2.5 m) of a fume disposal mechanism.

Ventilation Space

Provide 8" (20.3 cm) space on each side and 3" (7.6 cm) in the rear for ventilation.

System Dimensions and Weight

System dimensions are 21" W x 25" D x 25" H, weighing 140 lb without vessels.

Environmental Conditions

Location must be free from vibration and traffic, with temperatures between 41°F (5°C) and 104°F (40°C).

Power Outlet Requirement

System must connect to a dedicated, grounded outlet.

Ventilation and Electrical Specifications

Exhaust System

System uses an 8' flexible exhaust hose; hood/exhaust must draw at least 125 CFM.

Electrical Power Requirements

Requires 208/230V 60Hz or 200-240V 50Hz, 15A power with a 250V 15A or 20A rated receptacle.

MARS Series Installation Steps

Unpack System Components

Pull plastic tab, open handle, remove plastic assembly, and cut tape on inner box.

Prepare for System Placement

Lay box sides flat, remove foam, and lift system to bench top with two people.

Connect Exhaust and Power

Attach exhaust hose to the back and plug the power cord into a grounded outlet.

Power On and System Setup

Push power button, write down serial number, and determine/select line voltage.

Initial System Introduction

After restart, access 'Settings' > 'Video' > 'Welcome' for an introduction.

System Registration

Register your system by visiting www.cem.com/register for further details.

System Registration and Support

Register Your System

Register at www.cem.com/register to download software, method notes, and literature.

Account Management

Update your profile with your serial number to access more owner content.

Customer Support

Contact websupport@cem.com for assistance or service@cem.com for service inquiries.

CEM Service Commitment

CEM Service provides high-level technical support and service by certified technicians.