What to do if the Solvent/Extract Recovery is low in CEM EDGE system?
Low solvent or extract recovery in your CEM Laboratory Equipment may be due to empty solvent bottles. Ensure that the solvent bottles are adequately filled by adding solvent. It could also be caused by slow sample draining. To resolve this, increase the pore size of the Q-Disc. If you are working with cellulose, increase the C#.
How to fix a Possible System Clog in CEM EDGE system Laboratory Equipment?
A possible system clog in your CEM Laboratory Equipment can manifest as slow sample draining. Try increasing the pore size of the Q-Disc. For cellulose, increase C#. Another cause could be overfilled Q-Cups. If this is the case, clean the actuator. Check the “Routine Maintenance” and “Sample Preparation” sections for instructions and preventative measures.
What to do if Max Pressure is Exceeded in CEM EDGE system?
If the maximum pressure is exceeded with your CEM Laboratory Equipment, it's likely that the pressure generated at the current temperature exceeds the system's maximum pressure. To resolve this, decrease the method temperature or decrease the amount of sample being used.
Why are recoveries low with my CEM EDGE system Laboratory Equipment?
If you are experiencing low recoveries with your CEM Laboratory Equipment, it could be due to a hold time that is not long enough. Try increasing the hold time by 1 minute. Alternatively, the temperature may be incorrect. In this case, increase the temperature by 10 °C, or decrease it by 10 °C if you are working with temperature-sensitive analytes.
Why is the Q-Cup sticking to the actuator in my CEM Laboratory Equipment?
If the Q-Cup is sticking to the actuator in your CEM Laboratory Equipment, it might be because the Q-Cups are dirty. Try cleaning the Q-Cups. Another possible cause is that the Q-Cups are overfilled. In this case, clean the actuator. See “Routine Maintenance” for instructions. See “Sample Preparation” for preventative measures.
How to remove Particulates in extract from CEM EDGE system?
If you find particulates in the extract from your CEM Laboratory Equipment, it may be due to the porosity of the samples being less than that of the Q-Disc. Try decreasing the pore size of the Q-disc. For cellulose, decrease C#.
What to do if there is Water in the extract in CEM EDGE system Laboratory Equipment?
If there is water in the extract from your CEM Laboratory Equipment, the sample is likely wet. To resolve this, increase the amount of drying agent used.
Explains the meaning and use of safety alert words like NOTE, CAUTION, and WARNING.
Outlines crucial safety measures for operating and maintaining the EDGE instrument.
Details safety precautions specifically for sample preparation procedures.
Lists safety guidelines related to the system's heating capabilities and temperature settings.
Instructions for inspecting the EDGE system and its accessories upon delivery.
Step-by-step guide for connecting the exhaust, power, and installing the barcode scanner.
Steps for attaching solvent bottles and waste lines to the EDGE system.
Instructions for system recovery and autosampler homing procedures.
Steps for syringe emptying, rack insertion, and initial system settings customization.
Guide to setting language, date/time, and verifying autosampler calibration.
Details on verifying autosampler and waste calibration procedures.
Steps for performing pressure calibration and completing system setup.
Final steps for pressure calibration and confirmation of system setup completion.
Detailed instructions for preparing samples using Q-Cups and Q-Discs.
Steps for loading sample racks and verifying bottle positions for analysis.
Guide for selecting and assigning analytical methods to sample positions.
Instructions for starting sample analysis runs and monitoring their progress.
Details on assigning sample IDs, starting runs, and viewing run status.
Steps to input Q-Disc barcodes for sample analysis.
Comprehensive guide for creating custom analytical methods for the EDGE.
Instructions for modifying existing analytical methods.
Instructions for exporting sample and run data to a flash drive.
Detailed instructions for performing a full calibration of the autosampler system.
Continues the detailed steps for autosampler calibration, including tool usage.
Further instructions for autosampler calibration, focusing on alignment and drop-off points.
General| Brand | CEM |
|---|---|
| Model | EDGE system |
| Category | Laboratory Equipment |
| Language | English |
To Next Page
