Central Pneumatic 95275 Owner's Manual & Safety Instructions

Other manuals for Central Pneumatic 95275

Set Up And Operating Instructions16 pages

• T

  Timothy KeyAug 17, 2025

  Why is my Central Pneumatic 95275 not building enough pressure?

  

  Same questionReply

  • T

    Travis GriffinAug 17, 2025

    If your Central Pneumatic Air Compressor is not building enough air pressure, consider the following: 1. The compressor might not be large enough for the job. Check if the accessory SCFM is met by the compressor. If not, you may need a larger compressor. 2. There may be loose fittings. Reduce air pressure, check all fittings with a soap solution for air leaks, and tighten as needed, being careful not to overtighten. 3. The hose or hose connections may not be adequate. Replace them with a larger hose and/or hose connections. 4. High altitude may be reducing air output. If you are in a high altitude location, you may need a larger compressor. 5. The check valve may need service. Clean or replace it as needed.

    

    Reply
• L

  laurenfloresAug 21, 2025

  Why does my Central Pneumatic Air Compressor start and stop so often?

  

  Same questionReply

  • A

    Andrew VegaAug 21, 2025

    If your Central Pneumatic Air Compressor starts and stops excessively, it could be due to: 1. The compressor not being large enough for the task. Verify that the accessory SCFM is adequate for the compressor. If the compressor doesn’t reach the required SCFM, a larger compressor is needed. 2. Loose fittings. Reduce the air pressure and inspect all fittings using a soap solution to check for air leaks. Tighten the fittings as necessary, being careful not to overtighten them.

    

    Reply
• T

  tlopezAug 25, 2025

  How to fix air leaking from Central Pneumatic 95275 fittings?

  

  Same questionReply

  • R

    Robin SmithAug 25, 2025

    If air is leaking from the fittings of your Central Pneumatic Air Compressor, it is likely due to loose fittings. Reduce the air pressure, then check all the fittings with a soap solution for air leaks. Tighten them as needed, but do not overtighten.

    

    Reply
• N

  Nancy JacksonAug 28, 2025

  What to do if my Central Pneumatic 95275 Air Compressor tank is leaking air?

  

  Same questionReply

  • T

    Timothy McphersonAug 29, 2025

    If air is leaking from the tank of your Central Pneumatic Air Compressor, it is likely due to a defective or rusted tank. Have the tank replaced by a qualified technician.

    

    Reply
• J

  Janice GonzalezSep 1, 2025

  How to prevent my Central Pneumatic Air Compressor from overheating?

  

  Same questionReply

  • P

    Patricia CarsonSep 1, 2025

    If your Central Pneumatic Air Compressor is overheating, consider the following: 1. The environment may be unusually dusty. Move the unit to a cleaner environment. 2. The cord may be too small of a gauge or too long. Increase the cord size or use a shorter length extension cord, or eliminate the extension cord. 3. The unit may not be on a level surface. Reposition the unit on a level surface.

    

    Reply
• H

  harrispaigeSep 5, 2025

  What to do about moisture in the discharge air from my Central Pneumatic 95275 Air Compressor?

  

  Same questionReply

  • P

    parksnathanSep 5, 2025

    If you notice moisture in the discharge air of your Central Pneumatic Air Compressor, it may be due to too much moisture in the air. To resolve this, install an inline air filter/dryer, and/or relocate the compressor to a less humid environment.

    

    Reply
• J

  Joseph RamirezSep 9, 2025

  What does it mean when the safety valve “pops” on my Central Pneumatic 95275 Air Compressor?

  

  Same questionReply

  • S

    Stephen ThomasSep 9, 2025

    If the safety valve on your Central Pneumatic Air Compressor “pops,” it indicates that the safety valve needs service. Pull on the test ring of the safety valve; if it continues to pop, replace it.

    

    Reply

Central Pneumatic 95275 Specifications

General

Type	Pancake
Max Pressure	125 PSI
Air Delivery @ 40 PSI	2.6 SCFM
Air Delivery @ 90 PSI	2.0 SCFM
Voltage	120V

Related product manuals

Central Pneumatic 95498

15 pages

Central Pneumatic 95386

20 pages

Central Pneumatic 95630

14 pages

Central Pneumatic 95499

14 pages

Central Pneumatic 90234

16 pages

Central Pneumatic 94355

16 pages

Central Pneumatic 97080

14 pages

Central Pneumatic 93657

16 pages

Central Pneumatic 94667

11 pages

Central Pneumatic 93786

9 pages

Central Pneumatic 96068

10 pages

Central Pneumatic 94734

14 pages