Central Pneumatic 95386 Operating Instructions

Central Pneumatic 95386

16 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

8 GALL8 GALL

8 GALL8 GALL

8 GALL

ON 2 HPON 2 HP

ON 2 HPON 2 HP

ON 2 HP

AIR COMPRESSOR

Model 95386

OPERATING INSTRUCTIONS

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at: http://www.harborfreight.com

Copyright

©

2006 by Harbor Freight Tools

®

. All rights reserved. No portion of this

manual or any artwork contained herein may be reproduced in any shape or form

without the express written consent of Harbor Freight Tools.

For technical questions, please call 1-800-444-3353.

Due to continuing improvements, actual product may differ slightly from the product described herein.

Table of Contents

Other manuals for Central Pneumatic 95386

Set Up And Operating Instructions20 pages

Questions and Answers:

A
Amy WrightAug 18, 2025
What to do if my Central Pneumatic 95386 Air Compressor does not start?
- R
  reynoldsaaronAug 18, 2025
  If your Central Pneumatic Air Compressor does not start or restart, there are several things you can check: * Ensure the circuit matches the compressor requirements. * Reset the circuit breaker or have the outlet serviced. * Make sure the cord is securely plugged in. * Turn off the tool and compressor, wait for it to cool down, then press the reset button. * Reset the circuit or replace the fuse, checking for low voltage conditions. You might need to disconnect other appliances or move the compressor to its own circuit. * Fully bleed the tanks of air. * Use a larger diameter or shorter extension cord, or eliminate the extension cord altogether. If none of these steps work, have the unit inspected by a qualified technician.
W
William OrrAug 21, 2025
What to do if my Central Pneumatic Air Compressor is not building enough pressure?
- T
  thompsongregoryAug 21, 2025
  If your Central Pneumatic Air Compressor is not building enough air pressure, try the following: * Check the inlet and outlet filters and clean or replace them as needed. * Drain the oil and refill to the proper level with the recommended oil. * Clean or replace the air filter or muffler as needed. * Check if the accessory's SCFM (Standard Cubic Feet per Minute) requirement is met by the compressor. If the compressor cannot supply enough airflow, you may need a larger compressor. * Reduce the air pressure, then check all fittings with a soap solution for air leaks and tighten as needed, but do not overtighten. * Replace the existing hose and/or hose connections with larger ones. * Consider that you may need a larger compressor if you are in a high-altitude location.
R
rmillerAug 23, 2025
Why is my Central Pneumatic 95386 Air Compressor building pressure so slowly?
- M
  mvincentAug 23, 2025
  If your Central Pneumatic Air Compressor is building pressure too slowly, you can try the following: * Ensure the circuit matches the compressor requirements. * Drain the existing oil and refill to the proper level with the recommended oil. * Move the unit to a warmer location and verify that the recommended oil is in the crankcase. * Listen for air leaking from the valve; if there is a leak, replace it with an identical valve that has the same rating. * Reduce the air pressure and check all fittings with a soap solution for air leaks, then tighten them as needed, being careful not to overtighten.
J
jill55Aug 26, 2025
Why does my Central Pneumatic 95386 Air Compressor start and stop so much?
- G
  George ProctorAug 26, 2025
  If your Central Pneumatic Air Compressor starts and stops excessively, check the following: * Verify if the accessory's SCFM (Standard Cubic Feet per Minute) is met by the compressor. If the compressor doesn't reach the accessory's SCFM, you may require a larger compressor. * Reduce the air pressure, and then inspect all fittings for air leaks using a soap solution. Tighten the fittings as necessary, being careful not to overtighten them.
C
Clinton MeyerAug 28, 2025
How to fix high oil consumption in Central Pneumatic Air Compressor?
- C
  Charles CabreraAug 28, 2025
  To address high oil consumption in your Central Pneumatic Air Compressor: * Drain the existing oil and refill to the proper level with the recommended oil. * Ensure the unit is positioned on a level surface. * Clean the crankcase vent.
A
Amanda DunnAug 31, 2025
What causes my Central Pneumatic 95386 Air Compressor to overheat?
- C
  Chelsea McdanielAug 31, 2025
  If your Central Pneumatic Air Compressor is overheating, here are some steps to take: * Check the inlet and outlet filters, and clean or replace them as needed. * Drain the oil and refill to the proper level with the recommended oil. * Add oil to the proper level, and check for any leaks. * Clean and/or replace the filters more often, or move the unit to a cleaner environment. * Increase the cord size or use a shorter extension cord, or eliminate the extension cord altogether. * Reposition the unit on a level surface.
C
Christina TownsendSep 2, 2025
How to reduce excessive noise from Central Pneumatic 95386?
- T
  Thomas JonesSep 2, 2025
  To address excessive noise from your Central Pneumatic Air Compressor: * Drain the oil and refill to the proper level with the recommended oil. * Add oil to the proper level, and check for leaks. * Replace the belt guard. * Reduce the air pressure, then check all fittings with a soap solution for air leaks and tighten as needed, but do not overtighten. * Reposition the unit on a level surface.
J
johnny07Sep 5, 2025
Why is there oil in the discharge air of my Central Pneumatic 95386?
- W
  Wendy ReynoldsSep 5, 2025
  If you find oil in the discharge air of your Central Pneumatic Air Compressor: * Drain the oil and refill to the proper level with the recommended oil. * Clean the crankcase vents.
C
Chelsey AndersonSep 7, 2025
How to fix air leaks from pump or fittings on Central Pneumatic 95386?
- S
  Sandra HoweSep 7, 2025
  If air is leaking from the pump or fittings of your Central Pneumatic Air Compressor, reduce the air pressure, then check all fittings with a soap solution for air leaks and tighten as needed. Do not overtighten.
K
Kyle AllenSep 9, 2025
What to do if the safety valve on my Central Pneumatic 95386 Air Compressor keeps popping?
- C
  Christina BryanSep 10, 2025
  If the safety valve on your Central Pneumatic Air Compressor is popping, pull on the test ring of the safety valve. If it continues to pop, replace it.

Central Pneumatic 95386 Specifications

General

Brand	Central Pneumatic
Model	95386
Category	Air Compressor
Language	English

Related product manuals

Preview: Central Pneumatic 95498

Central Pneumatic 95498

Preview: Central Pneumatic 95630

Central Pneumatic 95630

Preview: Central Pneumatic 95275

Central Pneumatic 95275

Preview: Central Pneumatic 95499

Central Pneumatic 95499

Central Pneumatic 94355

Preview: Central Pneumatic 93786

Central Pneumatic 93786

Preview: Central Pneumatic 97080

Central Pneumatic 97080

Preview: Central Pneumatic 94734

Central Pneumatic 94734

Preview: Central Pneumatic 93657

Central Pneumatic 93657

Preview: Central Pneumatic 90234

Central Pneumatic 90234

Preview: Central Pneumatic 96068

Central Pneumatic 96068

Preview: Central Pneumatic 90385

Central Pneumatic 90385