To Next PageTo Next PageWhat to do if Char-Broil 463247310 Grill has flare-up?
If your Char-Broil Grill experiences a flare-up, it could be due to grease buildup. Clean the burners and the inside of the grill/firebox. Another cause might be excessive fat in the meat; trim the fat before grilling. Also, check for excessive cooking temperature and adjust it accordingly by lowering the temperature.
Why is there a sudden drop in gas flow or low flame in my Char-Broil 463247310?
A sudden drop in gas flow or low flame in your Char-Broil grill can be caused by several factors. First, check if you are out of gas in the LP cylinder. If not, the excess flow valve may have tripped. To fix this, turn off the knobs, wait 30 seconds, and light the grill. If flames are still low, turn off the knobs and LP cylinder valve, disconnect the regulator, reconnect it, perform a leak test, turn on the LP cylinder valve, wait 30 seconds, and then light the grill. Finally, a vapor lock at the coupling nut/LP cylinder connection could be the issue. Turn off the knobs and LP cylinder valve, disconnect the coupling nut from the cylinder, reconnect it, and try again.
What to do if one burner does not light from other burners on my Char-Broil 463247310?
If one burner on your Char-Broil Grill does not light from the other burners, it's likely due to grease buildup or food particles in the end(s) of the carryover tube(s). Clean the carry-over tube(s) with a wire brush.
What to do if Char-Broil 463247310 flames blow out?
If the flames on your Char-Broil grill blow out, it could be due to high or gusting winds. Turn the front of the grill to face the wind or increase the flame height. Another reason could be low LP gas, in which case you should refill the LP cylinder. It's also possible the excess flow valve has tripped; refer to "Sudden drop in gas flow" to resolve this.
What to do if my Char-Broil 463247310 has a persistent grease fire?
If your Char-Broil Grill has a persistent grease fire, it's likely due to grease trapped by food buildup around the burner system. To resolve this, turn the knobs to OFF and turn off the gas at the LP cylinder. Leave the lid in position and let the fire burn out. After the grill cools, remove and clean all parts.
What to do if my Char-Broil Grill has flashback (fire in burner tubes)?
If you experience flashback (fire in burner tubes) in your Char-Broil Grill, it indicates that the burner and/or burner tubes are blocked. Turn the knobs to OFF and clean the burner and/or burner tubes. Refer to the burner cleaning section of the Use and Care guide for detailed instructions.
Why Char-Broil 463247310 Grill timer does not work?
If the timer on your Char-Broil Grill does not work (the green light does not flash), it could be due to a dead battery. Replace the batteries. Alternatively, the batteries might be installed incorrectly; ensure they are installed correctly. Also, make sure the knob position started the Clean Cycle by pushing the knob in to start the clean cycle. The green LED should begin to flash.
How to fix Char-Broil Grill if no LEDs will illuminate?
If no LEDs illuminate on your Char-Broil Grill, it's likely due to a dead battery. Replace the batteries.
General| Brand | Char-Broil |
|---|---|
| Model | 463247310 |
| Category | Grill |
| Language | English |
Explains the meaning of DANGER, WARNING, CAUTION symbols used throughout the manual.
Steps to take if a gas leak is detected, including contacting authorities.
Crucial warnings about flammable liquids, LP cylinder storage, and residential use.
Warning against altering or repairing the hose/valve/regulator assembly.
Proper handling, storage, and safety precautions for LP cylinders.
Step-by-step guide to securely connect the regulator to the LP cylinder valve.
Procedure for testing LP cylinder connections for leaks using a soap solution.
Essential safety guidelines for operating the grill, including clearances and fire prevention.
Step-by-step instructions for safely lighting the main burners.
Sliding the grease tray in and installing the LP cylinder with regulator.
Solutions for gas leaks from hoses, cylinders, valves, and connections.
Diagnosing and resolving problems with ignitors, gas flow, and burner lighting.
