What to do if Chroma Power Supply shows OVER CURRENT protection (OCP)?
If the Chroma Power Supply indicates an OVER CURRENT protection (OCP) fault, it means the output current exceeds the specified limit or the set I LIMIT. To resolve this, remove the overload connected to the power supply or increase the I LIMIT setting.
What to do if Chroma 61604 shows OVER POWER protection (OPP)?
If your Chroma Power Supply displays an OVER POWER protection (OPP) message, it signifies that the output power is beyond its specification. To fix this, either decrease the output voltage or remove the excessive power draw from the connected load.
What to do if Chroma 61604 Power Supply shows OUTPUT SHORT protection?
If the Chroma Power Supply shows an OUTPUT SHORT protection error, it indicates a short circuit at the output or a reverse current flow. To resolve this: 1. Remove the short circuit. 2. Disconnect the load.
What to do if Chroma Power Supply shows OVER TEMP protection (OTP)?
If the Chroma Power Supply displays an OVER TEMP protection (OTP) warning, it means the unit is overheating. This could be due to: 1. High ambient temperature: Ensure the unit is operated within a 0 ~ 40°C environment. 2. Obstructed airflow: Clear any blockages from the air vents to allow proper ventilation.
What to do if Chroma Power Supply shows INPUT FAIL protection (UVP)?
If the Chroma Power Supply shows an INPUT FAIL protection (UVP) message, it means the AC source line input voltage is either too low or too high. You should measure the input voltage and adjust it if it's outside the specified range.
Why is Chroma Power Supply output distorted?
The distorted output from the Chroma Power Supply can be caused by: 1. AC source voltage being too low: Try programming a higher output voltage. 2. Rectified load being too large at high frequency: Reduce the load or lower the output frequency.
What to do if Chroma Power Supply shows OUTPUT OVP protection?
If the Chroma Power Supply displays an OUTPUT OVP protection message, it could be due to: 1. Remote sense being open: Connect the output to the remote sense terminals. 2. Output voltage peak exceeding the range: Check the settings of Vac and Vdc on the MAIN PAGE.
What to do if Chroma 61604 Power Supply shows INT _ AD protection?
If the Chroma Power Supply shows an INT _ AD protection message, it may be due to: 1. Line input voltage cycle dropout: Check the stability of the input voltage. 2. Instant over current of output: Remove the load. If the protection status persists, it may indicate damage to the AD power stage, and you should consult the dealer for assistance.
What to do if Chroma 61604 Power Supply shows INT _ DD protection?
If the Chroma Power Supply shows an INT _ DD protection message, it may be due to: 1. Line input voltage cycle dropout: Check the stability of the input voltage. 2. Instant over current of output: Remove the load. If the protection status persists, it may indicate damage to the DD power stage, and you should consult the dealer for assistance.
How to fix poor measurement of V, I on Chroma 61604 Power Supply?
Poor voltage and current measurements on the Chroma Power Supply can be caused by the aging of internal components, leading to deviations in their characteristics. Periodic calibration is required to maintain accuracy.
Details Chroma's warranty policy for its instruments, covering defects in material and workmanship.
Outlines essential safety precautions for operation, service, and repair to prevent hazards.
Highlights critical warnings like lethal voltage and potential for death from contact.
Explains various safety symbols used in the manual, including DANGER, WARNING, CAUTION, and NOTICE.
Details the technical specifications for AC/DC output ratings, measurement capabilities, and other parameters.
Specifies voltage and frequency requirements for the AC source input power.
Provides step-by-step instructions for connecting the power cord to the AC source.
Details how to connect the remote sense terminals for accurate voltage delivery at the load.
Describes the steps for powering on the AC source and the self-test sequence.
Lists software-based protections like OVER CURRENT, OVER POWER, and OUTPUT OVP.
Lists hardware-based protections including FAN FAIL, INT-AD, and OVER TEMP.
Guides users to enter the calibration procedure by selecting MANUAL CALI and entering a password.
Details the steps for calibrating output voltage and measurement accuracy.
Provides procedures for calibrating the current measurement accuracy of the AC source.
Details the self-test steps performed on power-on and lists potential error codes and their meanings.
Provides a table of common operating problems, their reasons, and suggested solutions.
Details commands for fetching and measuring AC/DC current, voltage, power, and frequency.
General| Model | Chroma 61604 |
|---|---|
| Category | Power Supply |
| Output Voltage | 0-300V |
| Number of Outputs | 1 |
| Display | LCD |
| Crest Factor | 3:1 |
| Voltage Resolution | 0.1V |
| Current Resolution | 0.01A |
| Operating Temperature | 0°C to 40°C |
| Storage Temperature | -20°C to 70°C |
| Interface | RS-232, GPIB |
| AC Input | 50/60Hz |
| Voltage Range | 0-150V |
| Distortion | ≤ 0.5% THD at full load |
To Next Page
