Cisco ASR 9000 Series Configuration Manual

Configuring Serial Interfaces on the Cisco ASR 9000 Series Router
Configuration Examples for Serial Interfaces
543
Cisco ASR 9000 Aggregation Services Router Interfaces and Hardware Component Configuration Guide
OL-26061-03
RP/0/0RP0RSP0/CPU0:router(config-if)# end
Uncommitted changes found, commit them? [yes]: yes
The following example shows how to configure the interval between keepalive messages to be 10
seconds:
RP/0/0RP0RSP0/CPU0:router# configure
RP/0/0RP0RSP0/CPU0:router(config)# interface serial 0/3/0/0/0:0
RP/0/0RP0RSP0/CPU0:router(config-if)# keepalive 10
RP/0/0RP0RSP0/CPU0:router(config-if)# commit
The following example shows how to modify the optional serial interface parameters:
RP/0/0RP0RSP0/CPU0:router# configure
RP/0/0RP0RSP0/CPU0:router(config)# interface serial 0/3/0/0/0:0
RP/0/0RP0RSP0/CPU0:Router(config-if)# serial
RP/0/0RP0RSP0/CPU0:Router(config-if-serial)# crc 16
RP/0/0RP0RSP0/CPU0:Router(config-if-serial)# invert
RP/0/0RP0RSP0/CPU0:Router(config-if-serial)# scramble
RP/0/0RP0RSP0/CPU0:Router(config-if-serial)# transmit-delay 3
RP/0/0RP0RSP0/CPU0:Router(config-if-serial)# commit
The following is sample output from the show interfaces serial command:
RP/0/0RP0RSP0/CPU0:Router# show interfaces serial 0/0/3/0/5:23
Serial0/0/3/0/5:23 is down, line protocol is down
Hardware is Serial network interface(s)
Internet address is Unknown
MTU 1504 bytes, BW 64 Kbit
reliability 143/255, txload 1/255, rxload 1/255
Encapsulation HDLC, crc 16, loopback not set, keepalive set (10 sec)
Last clearing of "show interface" counters 18:11:15
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
2764 packets input, 2816 bytes, 3046 total input drops
0 drops for unrecognized upper-level protocol
Received 0 broadcast packets, 0 multicast packets
0 runts, 0 giants, 0 throttles, 0 parity
3046 input errors, 1 CRC, 0 frame, 0 overrun, 2764 ignored, 281 abort
2764 packets output, 60804 bytes, 0 total output drops
Output 0 broadcast packets, 0 multicast packets
0 output errors, 0 underruns, 0 applique, 0 resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
Configuring a Serial Interface with Frame Relay Encapsulation: Example
The following example shows how to create a serial interface on a SPA with Frame Relay encapsulation
and a serial subinterface with a PVC on router 1:
RP/0/0RP0RSP0/CPU0:router# configure
RP/0/0RP0RSP0/CPU0:router(config)# interface serial 0/1/0/0
RP/0/0RP0RSP0/CPU0:router(config-if)# encapsulation frame-relay
RP/0/0RP0RSP0/CPU0:router(config-if)#frame-relay intf-type dce
RP/0/0RP0RSP0/CPU0:router(config-if)# no shutdown
RP/0/0RP0RSP0/CPU0:router(config-if)# end
Uncommitted changes found, commit them? [yes]: yes
RP/0/0RP0RSP0/CPU0:router# configure
RP/0/0RP0RSP0/CPU0:router(config)# interface serial 0/1/0/0.1 point-to-point

Cisco ASR 9000 Series Specifications

General

Brand	Cisco
Model	ASR 9000 Series
Category	Network Router
Language	English