15
ENGLISH
SETTING THE VIDEO
CHANNEL
For a push-button TV tuner
If CH 3 or 4 corresponding to the video channel cannot
be tuned on your TV, proceed as follows: set the VCR 3/
4 channel selector and the TV to CH 3 or 4, play back a
prerecorded tape and tune the TV to receive a sharp
colour picture from the video cassette recorder. Refer to
your TV owner's manual for details.
To view playback of a recorded tape, or to watch a
program selected by the VCR's channel selector, the
TV must be set to channel 3 or 4 (video channel).
When a TV is connected with the 75 ohm coaxial cable
only.
1 Press and hold 3 or 4 button on the remote control
for 3 seconds in standby mode. The TV/VCR
indicator will start to flash.
2 Turn ON the TV and set to CH 3 or 4 to correspond
with the channel selected in step 1.
3 Press the POWER button to turn on the VCR. The
power indicator will light.
4 Press the TV/VCR selector button to select the VCR
position. The TV/VCR indicator will light.
5 Select any channel to receive
a TV station in your area.
The channel number will
appear on the screen for about
4 seconds.
+0 #
This VCR can display on the TV screen in the
English, Spanish or French languages.
CHECK BEFORE YOU BEGIN
• Turn ON the TV and set to the video channel 3 or 4.
• Turn ON the VCR POWER button.
• Press the TV/VCR selector button to select the VCR
mode.
When a TV is connected with an audio/video cable,
turn the TV on and select the video input mode on the TV.
3 Press the TRACKING SET +
or – button to select the
desired language: English
(ENGLISH), Spanish
(ESPAÑOL) or French
(FRANCAIS), then press the
ENTER button.
4 Press the MENU button until the menu screen is
cleared.
〈
+
/
–
/ENTER/MENU
〉
LANGUAGE/IDIOMA/LANGUE
ENGLISH
FRANCAIS
ESPAÑOL
1 Press the MENU button.
Press the TRACKING SET +
or – button to select the
SYSTEM SETUP option, then
press the ENTER button.
SETTING THE CLOCK
NOTES: • After a power failure or disconnection of the
power, the timer settings will be lost. In this
case, reset the present time.
• Press the CANCEL button to move cursor
backward for correction.
1 Press the MENU button. Press
the TRACKING SET + or –
button to select the SYSTEM
SETUP option, then press the
ENTER button.
2 Press the TRACKING SET + or
– button to select the CLOCK
SET option, then press the
ENTER button.
3 Press the TRACKING SET + or
– button to set the month, then
press the ENTER button.
4 Set the day, year and time as in
Step 2.
You must set the date and time manually for timer
recordings.
EXAMPLE: Setting the clock to "8:30 AM" March, 26
(WED), 2003.
CHECK BEFORE YOU BEGIN
• Turn ON the TV and set to the video channel 3 or 4.
• Turn ON the VCR POWER button.
• Press the TV/VCR selector button to select the VCR
mode.
When a TV is connected with an audio/video cable, turn
the TV on and select the video input mode on the TV.
LANGUAGE SELECTION
á
ñ
• The day of the week will
automatically appear when
you set the year.
á
ñ
2 Press the TRACKING SET +
or – button to select the
LANGUAGE option, then
press the ENTER button.
á
ñ
á
ñ
• Press and hold down the button to increase/
decrease the minute by 10.
• After setting, the date and time will start functioning
automatically.
á
ñ
á
ñ
4F70301A E P14-19 22/12/04, 16:2215
To Next Page
Loading...
General