16
á
ñ
TO ADD/DELETE CHANNELS
1
Press the MENU button.
Press the TRACKING SET +
or
– button to select the CH
SETUP option, then press the
ENTER button.
2 Press the TRACKING SET + or
– button to select the ADD/DE-
LETE mode, then press the
ENTER button.
3 Select the desired channels to
be added or deleted using the
TRACKING SET + or – button.
4 Press the ENTER button if you
wish to DELETE the channel
from memory.
Press the ENTER button if
you wish to ADD the
unmemorized channel.
Repeat Steps 3 and 4 for each channel to be added
or deleted.
5 Press the MENU button three times after adding or
deleting all of the desired channels, to return to
normal TV viewing.
When you don't want to receive a weak signal
broadcast, the Blue Back Screen can be obtained by
selecting the NO NOISE BACKGROUND "ON". When
the unit is shipped from the factory, the NO NOISE
BACKGROUND is set to the "ON".
CHECK BEFORE YOU BEGIN
• Turn ON the TV and set to the video channel 3 or 4.
• Turn ON the VCR POWER button.
• Press the TV/VCR selector button to select the VCR
mode.
When a TV is connected with an audio/video cable,
turn the TV on and select the video input mode on the
TV.
á
ñ
á
ñ
SETTING THE CHANNELS
1 Press the MENU button.
2 Press the TRACKING SET + or –
button to select the CH SETUP
option, then press the ENTER
button.
3 Press the TRACKING SET + or –
button to select the TV/CATV mode.
4 Press the ENTER button to select
the TV or CATV mode. The arrow
indicates the selected mode.
5
Press the MENU button twice to return to normal TV viewing.
TV/CATV SELECTION
á
ñ
This VCR is equipped with a channel memory
feature which allows channels to skip up or down
to the next channel set into memory, skipping over
unwanted channels. Before selecting channels,
they must be programmed into the VCR’s memory.
In addition to normal VHF and UHF channels, this
VCR can receive up to 113 Cable TV channels. To
use this VCR with an antenna, set the TV/CATV
menu option to the TV mode. When shipped from
the factory, this menu option is in the CATV mode.
NOISE ELIMINATION
1 Press the MENU button, then
press the TRACKING SET + or
– button to select the SYSTEM
SETUP option. Then press
ENTER.
2 Press the TRACKING SET + or
– button to select the NO
NOISE BACKGROUND option.
3 Press the ENTER button to
select the ON position.
4 Press the MENU button twice
to return to normal TV viewing.
TV - VHF/UHF channels
CATV - CABLE TV channels
When shipped from the factory, the TV/CATV menu option is set to the
“CATV”(Cable Television) mode.
If not using CATV, set this menu option to the “TV” position.
TV/CATV MODE SELECTION
AUTOMATIC MEMORY TUNING
CHECK BEFORE YOU BEGIN
• Turn ON the TV and set to the video channel 3 or 4.
• Turn ON the VCR POWER button.
• Press the TV/VCR selector button to select the VCR mode.
When a TV is connected with an audio/video cable, turn the
TV on and select the video input mode on the TV.
á
ñ
1 Press the MENU button.
Press the TRACKING SET +
or
– button to select the CH
SETUP option, then press the
ENTER button.
2 Press the TRACKING SET +
or
– button to select the
AUTO CH MEMORY mode,
then press the ENTER button.
3 The auto tuning will start. The
channel display will count up
and when finished, the screen
returns to normal.
The VCR can receive a maximum of 181 channels by
presetting the channels into memory.
+0
á
ñ
á
ñ
á
ñ
á
ñ
4F70301A E P14-19 22/12/04, 15:4116
To Next Page
Loading...
General