35
TOOLS
c) Disconnect the feed pipe assembly (5) from the steering. Remove the sealing plate. Seal the pipe
assembly with a plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 mm ring spanner
d) Remove the bearing caps, take off the steering towards the left-hand side of the car . . . . . . . . . . . . 12 mm box spanner
11 Disconnect the hose (2) on the heating system, from the feed pipe and disconnect the heater pipe from the
steel tube, right-hand side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 mm box spanners
12 Disconnect the petrol feed pipe from the pump. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13 Disconnect the brake feed pipe, from the three-way union (41) (see Pl. 25) (spanner 2222-T, see Pl.72, fig.4) Spanner 2222-T
14 Disconnect the union (42) on the distribution block (spanner 2219-T or 2221-T, see Pl. 72, fig. 4), the
union plates on the hydraulic gear selector and on the clutch re-engagement control (47) (see Pl. 25) . . . Spanner 2219-T or
2221-T
8 mm ring spanner
15 Remove the left-hand suspension sphere. (strap wrench 2223-T, see Pl. 93, fig. 1) . . . . . . . . . . . . . . . . . Strap wrench 2223-T
16 Disconnect the feed pipe (43) and the delivery pipe (44) from the selector (see Pl. 25).
17 Disconnect the choke control from the carburettor lever .
Disconnect the accelerator control from the crosspiece of the throttle valve control. Disconnect the control
from the pivot on the scuttle and twist it towards the left . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 mm spanner
18 Disconnect the advance and retard control, from the contact breaker.
19 Disconnect the S pipe assembly from the gearbox.
Disconnect the speedometer cable from the gearbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 mm ring spanner
12 mm box spanner
20 Remove the pipe between the control valve and the rear brake accumulator (situated at the front)
(spanner 2222-T, see Pl. 72, fig. 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Spanner 2222-T
21 Remove the right-hand suspension sphere. Remove the heat insulating screen . . . . . . . . . . . . . . . . . . . . . 12 mm box spanner
22 Remove the nuts from the engine fixing studs on the rear side brackets . . . . . . . . . . . . . . . . . . . . . . . . . . 23 mm spanner
23 mm box spanner
23 Disconnect the flexible coupling (bibax) from the driving plates on the gearbox . . . . . . . . . . . . . . . . . . . 12 mm socket with
extension
24 Remove the brake protection covers. Unscrew the nuts (101) on the connecting cable (110) and remove the
end of the cable (102), from the lever (115) and from the lever (103) (see Pl. 141).
To Next Page
Loading...
