EasyManuals Logo

Claas RU 450 User Manual

Claas RU 450
31 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #3 background imageLoading...
Page #3 background image
297 925.0 - RU 450 I/1
Contens
1. General information
Introduction .......................................................................... 1.1 / 1
Introduction to the CLAAS Repair Manual ........................... 1.2 / 1
Especially important ............................................................. 1.2 / 1
Identification plate .......................................................... 1.2 / 1
General information for repairs ............................................ 1.2 / 1
Explanation of the picture symbols ...................................... 1.2 / 4
Safety ................................................................................... 1.3 / 1
Identification of warning and danger notices ................. 1.3 / 1
Important operation information ........................................... 1.3 / 1
Hydraulic equipment ...................................................... 1.3 / 2
Screws ........................................................................... 1.3 / 2
Technical data .................................................................... 1.4 / 1
Oil filling capacity for the gearbox .................................. 1.4 / 2
Machine overview RU 450 ................................................... 1.5 / 2
2. Auger trough
Auger trough ....................................................................... 2.1 / 1
Removing/putting on the left and right protection cover 2.1 / 1
Removing/putting on the crop guard and tube carrier ... 2.1 / 1
Removing/putting on middle crop guard and crop tube . 2.1 / 2
Replacing the feeder segments ..................................... 2.1 / 2
Replacing the middle inner feeder segment .................. 2.1 / 2
Replacing the feed shear bar. ....................................... 2.1 / 3
Changing and installing the guide plates ....................... 2.1 / 3
Replacing the feed plates .............................................. 2.1 / 3
Replacing the scrapers .................................................. 2.1 / 5
3. Machine frame
Removing/putting on the lock ........................................ 3.1 / 1
Removing/putting on left and right side of the supporting arm .
3.1 / 2
Installing the rotor transmission ..................................... 3.1 / 4
Putting in the angular transmission with the tapered clutch. .....
3.1 / 6
Replacing the tapered clutch ......................................... 3.1 / 7
Removing the supporting arm ....................................... 3.1 / 9
Installing the supporting arm ....................................... 3.1 / 11
4. Knife/Feed
Intermediate points .............................................................. 4.1 / 1
Removing/installing the intermediate points .................. 4.1 / 1
Removing/installing the support to the intermediate points. .....
4.1 / 1
Removing/putting on the sliding skid ............................. 4.1 / 1
Removing/putting on the position transmitter ................ 4.1 / 2
Removing/putting on the divider points ......................... 4.1 / 2
Removing/putting on the outer points ............................ 4.1 / 3
Removing/installing the intake plates ................................... 4.2 / 1
Removing/installing the left or right intake plates .......... 4.2 / 1
Removing/putting on the upper intake plates ................ 4.2 / 7
Removing/putting on the bottom intake plates .............. 4.2 / 8
Removing/installing the cutting disks ................................... 4.3 / 1
Replacing the knife on the cutting disks ........................ 4.3 / 1
Removing the cutting disks ............................................ 4.3 / 2
Installing the cutting disks .............................................. 4.3 / 3
Intake taper ......................................................................... 4.4 / 1
Removing the intake taper ............................................ 4.4 / 2
Replacing the overload clutch ....................................... 4.4 / 3
Removing/putting on the outside chamber bottom. ....... 4.4 / 3
Installing the intake taper .............................................. 4.4 / 4
5. Hydraulic
Hydraulic ............................................................................. 5.1 / 1
Removing the hydraulic cylinder ................................... 5.1 / 1
Taking apart the hydraulic cylinder ............................... 5.1 / 2
Putting the cylinder back together ................................. 5.1 / 5
Installing the hydraulic cylinder ..................................... 5.1 / 8
6. Special equipment
Removing/putting on the safety covers ............................... 6.1 / 1
Removing/putting on the guard rails ............................. 6.1 / 1
Removing/putting on the guard plate ............................ 6.1 / 1
Removing/putting on the protective covering ................ 6.1 / 2
Removing/putting on the left and right guard plate ....... 6.1 / 4
Removing/putting on the cover ..................................... 6.1 / 4
Lodged corn auger .............................................................. 6.2 / 1
Taking off the lodged corn auger .................................. 6.2 / 1
Installing the lodged corn auger .................................... 6.2 / 4
Autopilot .............................................................................. 6.3 / 1
Removing/putting on the sensor system ....................... 6.3 / 1
Removing/putting in the wiring harness ........................ 6.3 / 3
7. Drives
Auger drive .......................................................................... 7.1 / 1
Removing the auger drive ............................................. 7.1 / 1
Removing/putting on the bearing housing ..................... 7.1 / 4
Removing the feeder auger ........................................... 7.1 / 5
Putting in the feeder auger ............................................ 7.1 / 7
Installing the auger drive ............................................... 7.1 / 8
Replacing the comb feeders on the feeder trough ...... 7.1 / 12
Replacing the reinforcement on the feeder trough. ..... 7.1 / 13
Knife drive ........................................................................... 7.2 / 1
Removing/installing the entering transmission .............. 7.2 / 1
Removing/installing the main transmission ................... 7.2 / 2
Removing/installing the rotor transmission ................... 7.2 / 6
Bevel drive ........................................................................... 7.3 / 1
Removing/installing the bevel drive ............................... 7.3 / 1
Transmission ....................................................................... 7.4 / 1
General - Important information .................................... 7.4 / 1
Main transmission (B) .......................................................... 7.5 / 1
Taking apart the main transmission .............................. 7.5 / 1
Putting together the main transmission ......................... 7.5 / 9
Main transmission - Shift transmission (H) .......................... 7.6 / 1
Main transmission – Taking apart the shift transmission (H) ...
7.6 / 1
Main transmission – Putting together the shift transmission ....
7.6 / 15
Bevel transmission .............................................................. 7.7 / 1
Taking apart/putting together the bevel transmission ... 7.7 / 1
Putting together the bevel transmission ........................ 7.7 / 8
Rotor transmission .............................................................. 7.8 / 1
Taking apart the rotor transmission ............................... 7.8 / 1
Find manuals at http://best-manuals.com/search?&s=CLA-2979250

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Claas RU 450 and is the answer not in the manual?

Claas RU 450 Specifications

General IconGeneral
BrandClaas
ModelRU 450
CategoryFarm Equipment
LanguageEnglish

Related product manuals