Clarion CR705R - Page 3

@ Audio Mode indications and Description of Operation
Audio Control
Up/Down
Buttons
Audio Mode
VOL
volume
adjustment
BASS
bass
adjustment
TREB
treble
adjustment
BAL
left/right
balance
adjustment
FAD
front/rear
balance
adjustment
Centre Position
Fader Front
Note 1: In the balance and fader adjustment modes, the actual steps and the steps indicated on the display do not match due to the large number of
steps.
Note 2: The original display reappears approximately 5 seconds after the adjustments in the various audio modes.
Note 3: The various modes are set to the following values when the power is first turned on after the set is installed in the car: VOL 07,
BASS 0, TREB 0, BAL 00 and FAD 00.
2. Listening to the Radio
% Band Selection Button @
When you press button _ the reception band changes in the following
order:
U1—->U2—>MW/LW—>U1
(U1 and U2 are on the same reception frequency band.)
% Tuning Mode Selector Button (T-M) @&
Press the button (2 so that "MAN" appears on the display. The manual
tuning mode is now set. Tune into a station by pressing button 45) or
button . Unless you press button @§ or button @@ within 5 seconds
of switching to the manual tuning mode, the unit will return to the seek
tuning mode.
@ Manual Tuning
During FM reception, the frequency changes in steps of 0.05 MHz.
On MW, it changes in steps of 9 kHz, and on LW, in steps of 1 kHz.
1. Press the button @) to set the manual tuning mode.
2. When you press button (5) , the frequency increases, and when
you press button , it decreases.
@ Seek Tuning (Local/DX)
There are two sensitivity levels for seek tuning: DX seek, which will
tune in any broadcasting stations which can be received, and Local
seek, where only those stations with a sufficiently strong signal,
i.e. local stations, can be tuned in.
<DX Seek>
1. Press button @) for more than 2 seconds. "DX" appears on the
display then turns off.
2. Press button (5) to tune toward higher frequencies and press
button to tune toward lower frequencies. Tuning will stop
when a broadcast station is received.
<Local Seek>
1. Press button @) for more than 2 seconds. "LO" appears on the
display then turns off.
2. Press button (§) to move to higher frequencies, button to
move to lower frequencies. Tuning stops at a station with good
reception.
* Preset Buttons 1, 2,3,4,5and6@ ©
By pressing a Preset button you can instantly recall a station which has
been stored in memory.
¥%& When calling a broadcasting station, unless you release the Preset
button within 2 seconds, the displayed frequency will be stored at
the Preset button, so be careful.
* Storing Stations in the Preset Memory
6 radio stations can be stored in memory for each band.
1. Press button to select the reception band.
2. Press button for more than 2 seconds to store stations auto-
matically in the memory (Auto Store). If less than 6 stations are
stored in this process, or if you want to store a broadcasting
station with a weak signal, carry out the following steps.
3. Tune in the broadcasting station using Manual Tuning.
4. Press the desired Preset button for more than 2 seconds. The
sound will go off when you press the button, and when it comes
On again, the station has been stored.
%K Preset Scan/Auto Store Memory Button @&
@ Preset Scan
Press button . The broadcasting stations stored at Preset buttons
1 to 6 will be received in order for 5 seconds each.
When you press button again, or press one of the Preset buttons
1 to 6, this mode will be released. (When the unit is receiving on
FM, all the stations stored in U1 and U2 will be received in order.)
¥* If you press button for more than 2 seconds, the Auto Store
memory mode will become operative. All the stations stored in
the memory so far will be cleared, and new ones willbe stored
instead, so be careful.
@ Auto Store Memory
6 strong-signal broadcasting stations can be stored automatically
for each band. (See “Storing Stations in the Preset Memory".)
* Stations previously stored in the preset memory are cleared
when new ones are stored using Auto Store.
% Stereo Reception indicator
When a stereo broadcast is received, the “ST” indicator @ tights up.
3. RDS(Radio Data System) Operation
%* RDS Button &
Set the RDS mode by pressing the button @ , 80 the "RDS” indicator
(a) lights up When you press the button again, this mode is released.
1, When an BCS station is received, the programme name iscisplayed.
(PS:Programme Service Name)
2. If an emergency br2adcast is received while an RDS station is being
received , "ALARM" is displayed.The volume of the emergency
broadcast is automatically set at the pre-set value.
3. If good reception of the RDS broadcast becomes impossible in your
present location, the "RDS" indicator @ starts blinking.
4. When seek tuning is carried out in the RDS mode, only stations
broadcasting an RDS signal will be received.
5. @ Preset Scan in RDS Mode
When you press the button , Preset Scan will be czarried out
only on the ADS stations among the preset stations.
e@ Auto Store in RDS Mode
When you press the button for more than 2 seconds, only
RDS stations will be stored on the Preset buttons.
* Same-Programme Search
ARB4171R CR705R