Note:
Be sure
to
read this chapter referring
to
the front diagrams
of
chapter
"2.
CONTROLS" on page 3 (unfold).
Basic Operations
Be sure to lower the volume before
switching
off
the unit power
or
the ignition
key. The
unit
remembers its last volume
setting. If you
switch
the power
off
with the
volume up, when you switch the power back
on, the sudden loud volume may
hurt
your
hearing and damage the unit.
Turning
on/off
the
power
Note:
• Be careful about using this unit for a long time
without running the engine.
Ifyou drain the car's
battery too
far,
you may not be able
to
start the
engine
and
this can reduce the service life
of
the
battery.
1.
Press the [SRC] button.
2.
The illumination and display on the unit light
up. The unit automatically remembers its last
operation mode and will automatically switch
to display that mode.
3.
Press and hold the [SRC] button for 1 second
or longer to turn off the power for the unit.
Note:
• System check
The first time this unit is turned on after the wire
connections are completed, it must be checked
what equipment is connected. When the
power
is
turned on, the "SYSTEM
CHK"
appears in the
display, then the unit returns
to
the clock display
mode. The system check starts within the unit.
When the system check is complete, press the
[SRCj button again.
Selecting a mode
1.
Press the [SRC] button to change the
operation mode.
2.
Each time you press the [SRC] button, the
operation mode changes
in
the following
order:
Radio
mode'"
CD/MP3 mode
...
M-CATCHER
mode'"
Radio mode
...
Adjusting
the volume
1.
Turning the [ROTARY] knob clockwise
increases the volume; turning it
counterclockwise decreases the volume.
*The volume level
is
from 0 (minimum)
to
33
(maximum).
Switching
the
display
1.
Press the
[0]
button to select the desired
display.
2.
Each time you press the
[0]
button, the
display switches in the following order:
Main
display'"
Title
display'"
Clock display
...
Main display
...
*Once selected, the preferred display becomes
the display default.
When
a function adjustment
such
as
volume
is
made, the screen will
momentarily switch
to
that function's display,
then revert back
to
the preferred display
several seconds after the adjustment.
*When you have entered a title
in
a
CO/MP31
WMA,
it
appears
in
the display.
If
you have not
entered a title, "NO TITLE" appears
in
the
display instead. For information
on
how
to
enter a title, refer to the subsection "Entering
titles"
in
section "Operations Common
to
Each Mode".
Setting MAGNA BASS EXTEND
The MAGNA BASS EXTEND does not adjust the
low sound area like the normal sound adjustment
function, but emphasizes the deep bass sound
area to provide you with a dynamic sound.
*The factory default setting
is
off.
1.
Press and hold the [A-M] button for 1 second
or longer to turn on the MAGNA BASS
EXTEND effect. "M-B EX" lights in the
display.
2.
Press and hold the [A-M] button for 1 second
or longer to turn off the MAGNA BASS
EXTEND effect. "M-B EX" goes off from the
display.
Setting the Z-Enhancer
This unit are provided with 3 types of sound tone
effects stored
in
memory. Select the one you prefer.
*The factory default setting
is
"Z+
OFF".
Each time you press the [Z] button, the tone
effect changes
in
the following order:
"Z-EHCER 1" ... "Z-EHCER 2" ... "Z-EHCER 3"
...
"Z+
OFF"'"
"Z-EHCER
1"
...
•
Z-EHCER
1 : bass emphasized
•
Z-EHCER
2 : treble emphasized
•
Z-EHCER
3 : bass and treble emphasized
• Z+
OFF
: no sound effect
DB455MC
11
To Next Page
Loading...
