Radio Operations
FM Reception
For enhanced
FM
performance the
mRIiI:rUNE~
tuner includes signal actuated stereo control,
Enhanced Multi AGC, Impulse noise reduction
curcuits and Multipath noise reduction circuits.
Changing the reception area
This unit
is
initially set to USA frequency intervals
of 10 kHz for AM and 200 kHz for
FM.
When using
it outside the USA, the frequency reception range
can be switched to the intervals below.
• Setting the reception area
1.
Press BND button
[1Q]
and select the desired
radio band (FM or AM).
2.
While pressing DISP button
ITI],
each time you
press and hold the number "6" of the Preset
buttons
00
for 2 seconds or longer, the re-
ception area switches from inside the USA to
outside the USA or from outside the USA to
inside the USA.
*
Any
station preset memories are lost
when
the
reception area
is
changed.
Listening to the radio
1.
Press FNC button [I] and select the radio
mode. The frequency is displayed.
2.
Press BND button
[1Q]
and select the radio band.
Each time the button is pressed, the radio
reception band changes
in
the following order:
FM
1
...
FM2
...
FM3 ... AM
...
FM
1
...
3.
Press the right or left side of SEARCH button
!TIl
to tune
in
the desired station.
Tuning
There are 3 types of tuning mode available, seek
tuning, manual tuning and preset tuning.
Seek
tuning
1.
Press BAND button
[1Q]
and select the desired
band. (FM or AM)
* If "MANU"
is
lit
in
the display, press and hold
BAND button
[Q]
for 1 second or longer.
"MANU"
in
the display goes off
and
seek tuning
is
now available.
2.
Press the right or left side of SEARCH button
!TIl
to automatically seek a station.
When the right side of SEARCH button
!TIl
is
pressed, the station is sought
in
the direction
of
higher
frequencies;
if
the
left
side
of
SEARCH button
~
is pressed, the station is
sought
in
the direction of lower frequencies.
Manual tuning
There are 2 ways available: Quick tuning and step
tuning.
When you are
in
the step tuning mode, the fre-
quency changes one step at a time.
In
quick tun-
ing mode, you can quickly tune the desired fre-
quency.
1.
Press BND button
[Q]
and select the desired
band (FM or AM (MW/LW)).
* If "MANU"
is
not lit
in
the display, press
and
hold
BND
button
[Q]
for 1 second or longer.
"MANU"
is
lit
in
the display and manual tuning
is
now available.
2.
Tune into a station.
• Quick tuning:
Press
and
hold
the
right
or
left
side
of
SEARCH button
~
for 1 second or longer to
tune
in
a station.
• Step tuning:
Press the right or left side of SEARCH button
~
to manually tune
in
a station.
Recalling a preset station
A total of 24 preset positions (6-FM1, 6-FM2, 6-
FM3, 6-AM) exists to store individual radio sta-
tions
in
memory. Pressing the corresponding pre-
set button
00
recalls the stored radio frequency
automatically.
1.
Press BND button
[1Q]
and select the desired
band (FM or AM (MW/LW)).
2.
Press the corresponding Preset button
00
to
recall the stored station.
* Press and hold one of Preset buttons
[[)
for 2
seconds or longer
to
store that station into pre-
set
memory.
Manual memory
1.
Select the desired station with seek tuning,
manual tuning or preset tuning.
2.
Press and hold one of Preset buttons
00
for 2
seconds or longer to store the current station
into preset memory.
Auto store
Auto store is a function for storing up to 6 sta-
tions that are automatically tuned
in
sequentially.
If 6 receivable stations cannot be received, a pre-
viously stored station remains unoverwritten at
the memory position.
1.
Press BND button
[IQ]
and select the desired
band (FM or AM (MW/LW)).
To Next Page
Loading...
Need help?
General
