8
English
M255
Basic Operations
Note:Be sure to read this chapter referring to the front diagrams of
chapter “2. CONTROLS” on page 3.
Lower the volume level before powering the
unit off. The unit stores the last volume set-
ting. If the unit is powered off with the volume
up, when the unit is powered back on, the sud-
den loud volume may harm your hearing and/
or damage the unit.
Setting the Z-Enhancer
The unit provides 3 types of sound tone effects,
stored in memory. Select the one you prefer.
∗ The factory default setting is “Z-EHCR OFF”.
Each time you press the [
Z
] button, the tone ef-
fect changes in the following order:
“Z-ENHANCER 1”
ÆÆ
ÆÆ
Æ “Z-ENHANCER 2”
ÆÆ
ÆÆ
Æ “Z-
ENHANCER 3”
ÆÆ
ÆÆ
Æ “Z-EHCR OFF”
ÆÆ
ÆÆ
Æ “Z-EN-
HANCER 1”...
• Z-ENHANCER 1 : bass emphasized
• Z-ENHANCER 2 : treble emphasized
• Z-ENHANCER 3 : bass and treble emphasized
• Z-EHCR OFF : no sound effect
7.OPERATIONS
CAUTION
!
Audio mode adjustments
Press the
[
A-M
]
button to select the adjustment
mode. The mode switches as follows each time
the
[
A-M
]
button is pressed:
BASS
ÆÆ
ÆÆ
Æ TREB
ÆÆ
ÆÆ
Æ BAL
ÆÆ
ÆÆ
Æ FAD
ÆÆ
ÆÆ
Æ Previous mode
∗ The display returns to the previous mode 7 sec-
onds after the adjustment.
Adjusting the bass
1. Press the
[
A-M
]
button and select “BASS”.
2. Turning the
[
ROTARY
]
knob clockwise empha-
sizes the bass; turning it counterclockwise at-
tenuates the bass.
∗ The factory default setting is “0”.
(
Adjustment
range: –7 to +7
)
Turning on/off the power
1. Press the
[
FNC
]
button.
2. The illumination and display on the unit light
up. The unit automatically remembers its last
operation mode and will automatically switch
to display that mode.
3. Press and hold the
[
FNC
]
button for 1 second
or longer to turn off the power for the unit.
Selecting a mode
1. Press the
[
FNC
]
button to change the opera-
tion mode.
2. Each time you press the
[
FNC
]
button, the op-
eration mode changes in the following order:
Radio mode
ÆÆ
ÆÆ
Æ CD mode
ÆÆ
ÆÆ
Æ Radio mode...
Note:
• If the CD mode is selected when no disc is inserted,
the display shows “NO DISC”.
Adjusting the volume
Turning the
[
ROTARY
]
knob clockwise increases
the volume; turning it counterclockwise decreases
the volume.
∗ The volume level is from 0 (minimum) to 33 (maxi-
mum).
Adjusting the treble
1. Press the
[
A-M
]
button and select “TREB”.
2. Turning the
[
ROTARY
]
knob clockwise empha-
sizes the treble; turning it counterclockwise
attenuates the treble.
∗ The factory default setting is “0”. (Adjustment
range: -7 to +7)
Note:
• Bass and Treble can only be adjusted when the "Z-
enhancer" is off.
To Next Page
Loading...
Need help?
General
