Clarion NX603 User Manual

22 NX603/FX503
English
sAudio sometimes is not output in the iPod
mode when Bluetooth Audio is playing or
hands free calls are being made while the
iPod touch or iPhone is still connected
via Bluetooth. Perform operations from
the iPod touch or iPhone main unit,
and switch the settings (audio output)
from Bluetooth (CAR-BT) to the Dock
connector. Also, remove the iPod from
the unit and reconnect it. For details, refer
to the User’s Manual for the connected
device.
sAudio is sometimes not output from
the USB-connected iPod touch or
iPhone if the audio device is connected
via Bluetooth. In this case, switch the
Bluetooth connection mode to other than
[Playing music], and reconnect iPod touch
or iPhone.
p
P.40
MEMO
sWhen iPod operation is stopped,
operations sometimes become possible
by selecting a tune or video from the
category list.
sIf an error message is displayed, remove
the iPod from the unit and reconnect it.
sIf the iPod becomes inoperable, reset the
iPod main unit and reconnect it.
Reset methods (examples)
- iPod:
Simultaneously hold down the “Center”
and “Menu” buttons until the Apple
logo is displayed.
- iPod touch:
Simultaneously hold down the “Sleep/
Cancel sleep” and “home” buttons until
the Apple logo is displayed.
For details on how to reset the iPod,
check in the User’s Manual for the iPod.
✽
If operation is not remedied by resetting
and reconnecting the iPod, reset the
iPod, check operation of the iPod in
an unconnected state and then try
connecting it again.
Listening to iPod/viewing
iPod video
Connectible iPods
The unit supports the following devices: 5th
generation iPod, iPod classic
®
, iPod nano
®
,
iPod touch
®
, iPhone 3G, iPhone 3GS,
iPhone 4, iPhone 4S.
For more details, see the table below. The
iPod is not supplied with the unit. Use your
own iPod. To play ipod
,
CCA-750 (sold
separately) is required.
When an iPod is used on the unit, the iPod
firmware must be the most recent.
Connectible iPod Remarks
iPod (5th generation) Video can be
played.
iPod classic (80GB,
120GB, 160GB)
Video can be
played.
iPod nano
(1st generation, 2nd
generation)
iPod nano (3rd generation,
4th generation, 5th
generation)
Video can be
played.
iPod nano (6th generation)
iPod touch (1st generation
✽
) Video can be
played.
iPod touch (2nd
generation, 3rd generation,
4th generation)
Video can be
played.
iPhone 3G/iPhone 3GS/
iPhone 4/iPhone 4S
Video can be
played.
✽
Video can be played from firmware 2.0
onwards. In firmware versions older than 2.0,
use only in the music mode.
Attention
sBe sure to remove the iPod after the
vehicle’s engine key is turned to the
"OFF" position. The iPod’s power supply
might run down if it is not turned off while
still connected to the unit.
Notice
siPad/iPad2 are not supported.
sNot all iPod operations are guaranteed.
sSome iPods sometimes do not operate
depending on their firmware version
even if they are in the list of connectible
models.
sWhen connecting an iPod to the unit,
do not use iPod headphones or other
accessories.
sSome functions are restricted depending
on the iPod model and firmware version.
For information about connectible models,
refer to the following web site:
http://www.clarion.com/us/en/support/
compatibility/ipod/index.html
sThe iPod might not operate correctly
when the iPod’s track repeat function is
set.
sThe iPod might not operate correctly
when the iPod’s shuffle function is set.
In this case, cancel the shuffle function
before using the iPod.
sThe iPod sometimes is not recognized
when only video files are saved to it. This
problem is resolved when even one music
file is saved.
sWhen there are lots of tunes to play,
the titles or list sometimes cannot be
displayed depending on the iPod model.

Clarion NX603 Specifications

General

Brand	Clarion
Model	NX603
Category	Car Receiver
Language	English