14 DXZ935
English
Adjusting the balance
1. Press the [A-M] button and select “BAL-
ANCE”.
2. Turning the [ROTARY] knob clockwise em-
phasizes the sound from the right speaker;
turning it counterclockwise emphasizes the
sound from the left speaker.
∗ The factory default setting is “0”. (Adjustment
range: L13 to R13)
3. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
Adjusting the fader
1. Press the [A-M] button and select “FADER”.
2. Turning the [ROTARY] knob clockwise em-
phasizes the sound from the front speakers;
turning it counterclockwise emphasizes the
sound from the rear speakers.
∗ The factory default setting is “0”. (Adjustment
range: F12 to R12)
3. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
Operation BASS/TREB
1. Press the “BASS/TREB” mode. Each time
the [EQ] button is pressed, the adjusting item
“BASS” or “TREB” is changed cyclically.
2. Turn the [ROTARY] knob clockwise or coun-
terclockwise to adjust “BAS/TREB”.
3. Press the [EQ] button to return to the previ-
ous mode.
∗ The Adjustment range is from –6dB to +6dB
for bass and treb.
∗ This parameter is reflected STD PRO mode
Speaker Setting
You can set up your favorite sound environment
using “Dolby Surround Pro logic II ” or “AC-
Processor II ” so that you can enjoy a dynamic
sound of 5.1 ch surround or 4ch + 2ch speaker.
● Dolby Pro Logic II 5.1ch surround
Center SP +Front L.R. +Surround L.R. +Sub
Woofer.
To make the most of the sound field reproduc-
tion of Dolby Pro Logic II , a speaker system of
5.1 channel is recommendable. It has been also
designed so that a sound filed effect almost as
good as that of 5.1 channel reproduction can be
obtained even by a constitution of 4 channel + 1
channel (subwoofer).
If you using Dolby Pro Logic source and your
speaker is only four Front L.R. + Surround L.R.,
speaker setting will be better to CTR+SW and
CTR OFF, so Center channel divided to Front
L.R. automatically.
Note
• When SW-L + SW-R are chosen, audio output
from SW-L is not available in the PL
II
mode.
● AC-Processor II
Front L.R. + Rear L.R.+ Sub Woofer L.R. (4ch +
2ch)
To make the most of the sound field reproduc-
tion of AC-Processor II , a speaker system of 4
channel + 2 channel is recommendable.
1. Press and hold the [TITLE] button for 1 sec-
ond or longer and enter “ADJ” mode.
2. Press the [a] or [d] button to select the
“SP-SETTING”.
3. Turn the [ROTARY] knob clockwise or coun-
terclockwise to select “SW L+SW R” or “CTR
+SW” mode.
Note:
• When CTR + SW are chosen, audio output from
CTR is not available except in the PL
II
mode.
Center Speaker and Sub Woofer On / Off
Select PLII Mode on and SP setting to
“CTR+SW” mode
1. Press and hold the [TITLE] button for 1 sec-
ond or longer.
2. Press the [a] or [d] button to select the
“SP SEL”.
3. Press the [ ] button to adjust the “CTR-
SP” “SUB W”.
4. Turn the [ROTARY] knob clockwise or coun-
terclockwise to select “ON” or “OFF”.
∗ This function is useful for Speaker Setting
Problems.
Filter Adjustment
1. Select Dolby Pro Logic II or AC-ProII mode
and press and hold the [TITLE] button for 1
second or longer.
2. Press the [a] or [d] button to select the
“FILTER”.
3. Press the [ ] button to adjust the “SUB-W
LPF” or “HPF”.
4. Turn the [ROTARY] knob clockwise or coun-
terclockwise to adjust filter frequency.
Basic Operations
To Next Page
Loading...
