Clarion PU-9907A - Page 3

PTY (Programme Type)
The
PTY
function
enables
you
to
give
the
selected
PTY
broadcast
listening
priority
when
it
begins.
Press
RDS
button
40)
for
more
than
2
seconds,
PTY
name
will
be
displayed.
PTY
mode
can
be
selected
by
pushing
preset
button
&
or
tuning
button
©.
5
sec-
onds
later
after
selecting
PTY
mode,
“PTY”
indicator
will
be
illumi-
nated
and
back
to
previous
mode.
When
you
press
button
@0
again,
the
PTY
wait
state
is
released.
However,
if
you
press
this
button
during
a
PTY
broadcast,
the
PTY
broadcast
is
cancelled
and
the
PTY
broadcast
wait
state
becomes
operative
again.
When
the
selected
PTY
broadcast
is
received,
it
is
reproduced
on
your
unit.
*
Inthe
traffic
information
wait
state,
traffic
information
broad-
casts
have
priority
over
PTY
broadcasts.
recy g
on ee
TAPE OPERATION
@
®
@
@®O
QO
@®
@
Cassette
Tape
Slot
Door
Metal
Tape
Detection
Correct
equalization
is
automatically
selected
according
to
the
tape
used.
When
you
insert
a
70
psec.
tape
(such
as
a
CrO,,
FeCr,
or
METAL
tape),
the
unit
detects
and
switches
the
tape
equalization
to
70
usec.
The
“MTL”
indicator
will
light.
@ EJECT Button
@Play/Programme Switch
@
Fast
Forward/Rewind
Button
(APC
(Auto
Programme
Control)
Switches
©Mode Select Switch
When
listening
to
the
radio
and
a
tape
has
been
inserted,
pressing
this
switch
will
switch
from
the
tuner
to
tape
deck
operation
and
play-
back starts automatically.
@ Blank Skip Switch (BLS)
@Dolby NR Switch (B NR)
(@ Tape Scan Switch (SCN)
@ Repeat Switch (RPT)
4) TA (Traffic Announcement) Button
When
traffic
information
begins,
this
is
given
top
listening
priority.
When
you
press
the
TA
button,
the
“TA”
indicator
lights
up,
and
a
traffic
information
station
is
sought.
If
such
a
station
is
found,
the
“TP”
indicator
lights
up,
and
the
traffic
information
wait
state
becomes
operative.
When
you
press
the
TA
button
again,
this
state
is released.
lf
you
press
the
TA
button
while
listening
to
traffic
information,
the
traffic
information
broadcast
is
cancelled
and
the
traffic
information
wait state becomes operative again.
If
no
traffic
information
station
is
found,
“NO
TRA”
is
displayed,
so
you
then
press
the
TA
button
to
release
the
state.
Traffic
information
is
automatically
reproduced
at
the
preset
volume.
1.
When
the
traffic
information
begins,
“TRA
INFO”
is
displayed
for
about
5
seconds,
after
which
the
PS
(Programme
Service
Name)
or
frequency
is
displayed.
2.
While
you
are
listening
to
traffic
information,
loudness
is
turned
OFF.
3.
Even
if
the
“TA”
indicator
is
lit,
when
a
station
not
broadcasting
traftic
information
is
being
received,
a
traffic
information
station
will
be
sought
when
you
press
the
TA
button.
4. ¢ Preset Scan when “TA” indicator is Lit:
When
you
press
the
PS
button
(9),
only
stations
broadcasting
traffic
information
will
be
covered
by
the
Preset
Scan.
e Auto Store when “TA” indicator is Lit:
If
you
press
the
AS
button
(9)
for
more
than
2
seconds,
only
stations
broadcasting
traffic
information
will
be
auto
stored.
CD CHANGER CONTROL OPERATION
D@®@Q® @®
123 80S SCO PTY TR fa Cow Bt anh
BGREREEES
® Cw)
() MODE Selector Switch (CD)
This
switch
is
used
to
switch
from
the
tuner
or
cassette
deck
to
the
CD
Changer
mode.
CD
playback
starts
when
this
switch
is
pressed
from the Tuner or Cassette mode.
When
the
CD
Selector
Switch
is
pressed,
the
power
to
the
CD
Changer
is
switched
on,
and
playback
starts
from
the
first
track
on
the first disc. (First time only)
If
no
magazine
has
been
set
in
the
CD
Changer,
“NO
MAGA2’
will
be displayed.
When
the
CD
Selector
Switch
is
pressed,
the
display
will
first
show
the
disc
number,
and
after
that
the
track
number.
During
actual
disc
play,
both
the
track
and
the
played
time
will
be
displayed.
Refer to the figure on the next page for the display messages:
PU-9907A