Coleman DURANGO 2000000143 User Manual

DURANGO
TM
15’ X 10’ MODEL 2000000143
STITCH LINE
Fig. 1
Fig. 7
To Set Up Tent
1. Unfold tent and spread out on a clean, level surface with the
door facing the desired direction. Unzip door.
2. Stretch out corners and sides of tent. Secure with stakes
driven in at an angle to better anchor the tent. (Fig. 1 & 2)
Note: Staking the corners and sides will make it easier to
raise and tear-down the tent.
7. Insert one end of each black pole
into pins located on the ring in
center location at the back of the
tent. (Fig. 7)
8. Insert other end of black poles
into pins at front corners of tent;
and end of gray pole into pins on
sides of tent to form arches as
shown. (Fig. 8)
Fig. 8
Before you begin
Read all instructions before set up.
• Select a level campsite clear of rocks, branches, and other hard
or sharp objects, to install your tent.
WARNING: Keep clear of overhead power lines.
• Do not set up your tent under trees.
• For best results in windy conditions, position end of tent into
the wind.
• Enlist the help of at least one other person to assist you when
it is time to assemble the tent.
Parts and Components
Description Part Number
Main Poles, Black (2) 9163-1051
Side Pole, Gray (1) 9163-1061
Roof Ridge Pole, Black (1) 9163-1071
Rainfly Pole, Black (1) 9163-1081
Rainfly 9163-1091
3. Assemble roof ridge pole (3-section, black, shock-corded
pole) and insert through sleeve in center of tent.
4. Place one end of roof ridge pole in brass grommet. Carefully
apply pressure on pole to allow other end of pole to bow and
be inserted into other brass grommet. (Fig. 3 & 4)
Fig. 2
Fig. 3
Fig. 4
5. Assemble the 2 long, black shock-corded poles and insert
through sleeves in top of tent forming an “X” as shown.
(Fig. 5)
Fig. 5
6. Assemble gray, shock-corded, side pole and insert through
sleeve in front of tent as shown. (Fig. 6)
Fig. 6
First
Black Pole
Gray
Pole
Gray
Pole
Second
Black Pole
9. Attach frame clips along tent seams to gray side pole and
both black poles. (Fig. 9 & 10)
Fig. 9
Fig. 10
To Attach Rainfly
1. Drape rainfly over tent. Make sure end with logo is centered
over the door and the rainfly seams are centered over the
gray and black
poles. (Fig. 11)
Fig. 11
(continued on
other side)

Coleman DURANGO 2000000143 Specifications

General

Brand	Coleman
Model	DURANGO 2000000143
Category	Tent
Material	Polyester
Doors	1
Poles Material	Fiberglass
Setup Time	10 minutes
Center Height	6 ft
Windows	Yes
Ventilation	Yes

Summary

Tent Setup Instructions

Prepare Tent Site and Unfold

Select a level campsite, unfold tent, unzip door, and stretch out corners and sides.

Install Tent Poles

Assemble and insert roof ridge pole, main poles, and side pole to form tent arches.

Attach Frame Clips

Attach frame clips along tent seams to the gray side pole and both black poles.

Rainfly Attachment

Drape and Secure Rainfly

Drape rainfly over tent, center logo over door, and secure with clips and fasteners.

Install Rainfly Pole

Assemble and insert the shock-corded rainfly pole into the underside sleeve.

Tie Guylines

Tie guylines at four locations on the tent and secure them with stakes.

Manage Tent Doors

Instructions for fully opening a tent door or using the door vent.

Tent Features and Storage

Room Divider Installation

Install the room divider panel by inserting toggles through fabric loops.

Accessory Storage and Access

Utilize overhead storage, side pockets, and cooler access for convenience.

Electrical Cord Management

Use the designated access panel for safe outdoor electrical cord entry.

Proper Tent Storage

Clean, dry, and neatly fold the tent and poles into the carry case for storage.

Important Usage Information

Condensation Management

Understand condensation causes and minimize it through ventilation.

Tent Care and Maintenance

Dry tent thoroughly, avoid packing stakes inside, and never pull tent to remove stakes.

Pole Storage and UV Exposure

Do not telescope poles for storage; UV rays can damage tent material.

Flame Resistance Warning

Keep tent fabric away from flame sources; CPAI-84 requirements met.