Name: ComAp intelilite nt amf20
Brand: ComAp
Rating: 4 (1 reviews)

To Next Page

To Previous Page

InteliLite

IL-NT-AMF-2.2-Reference Guide.pdf

Connection description

The following diagrams show how to connect the engine control unit to the InteliLite controller:

Engines with J1939 support started via CAN bus

VOLVO PENTA engines (EMS II, EDC III units)

Table of Contents2
General Guidelines5
- What Describes this Manual5
- Warnings5
- Symbols5
- Text6
- Dangerous Voltage6
- Adjust Set Points6
General Description7
- Description of the Controller System (with All Options)7
- What Is in the Package7
- IL-NT RS232 Communication Plug-In Card7
- IL-NT RS232-485 Communication Plug-In Card11
- IL-NT S-USB Service USB Communication Plug-In Card12
- IB-Lite Ethernet Communication Plug-In Card13
- IL-NT-GPRS GSM and GPRS Plug-In Modem14
- IL-NT AOUT8 Gauge Driver Module15
- IL-NT BIO8 Hybrid Binary Input/Output Module17
- IC-Nt Ct-Bio718
- IL-NT RD Remote Display Software18
- Remote Annunciator IGL - RA1518
- IG IOM/PTM Module19
- IG-IB Internet Bridge20
- Internetbridge-NT21
IL-NT Terminals22
- IL-NT Terminals and Front Face22
Installation23
- Mounting23
- Dimensions24
Recommended Wiring25
- AMF - Wiring Diagram25
Contactors (Set Point MCB Logic = "CLOSE-OFF")26
ATS with Two Stable Positions (Set Point MCB Logic = "CLOSE-ON")26
Stand-By Applications26
ATS with Three Stable Positions (Set Point MCB Logic = "CLOSE-OFF")27
- Dual Mutual Standby (Dual AMF) Application27
Getting Started30
- How to Install30
- Current Measurement34
- Earth Fault Measurement (Module)36
- Voltage Measurement and Generator Connection Types37
- Analog Inputs40
- Binary Inputs and Outputs46
- Recommended CAN/RS485 Connection47
- Extension Modules (CAN Bus) Connection49
Inputs and Outputs50
- Binary Inputs IL-NT - Default50
- Binary Inputs - List50
- Binary Outputs IL-NT - Default54
- Binary Outputs - List55
- Analog Inputs65
- Analog Outputs65
Setpoints66
- Password66
- Basic Settings66
- Comms Settings70
- Engine Params73
- Engine Protect77
- Gener Protect79
- AMF Settings81
- Extension I/O85
- Date/Time85
- Sensors Spec87
- SMS/E-Mail87
- Alternate Cfg89
- Earthfaultprot90
ECU-Controlled Engine Support92
- Identifying Configured ECU93
- Values Read from ECU93
- Diagnostic Messages Read from ECU94
- Analog Inputs94
- Connection Description95
Sensor Specification98
- Background of the Sensor Calibration98
- Default Sensor Curves98
Function Description99
- OFF Mode99
- MAN Mode99
- AUT Mode101
- TEST Mode102
- Circuit Breakers Timing102
Alarm Management105
- Sensor Fail (FLS)105
- Warning (WRN)105
- Breaker Open and Cooling (BOC)105
- Shut down (SD)106
- Mains Failure (MF)106
- Voltage Phase Sequence Detection106
Gen-Set Operation States108
- List of Possible Events110
- History File112
Init Screens115
- Customer Logo Screen115
- Firmware Init Screen115
- Language Screen115
- User Interface Screen115
Remote Control and Data Logging116
- PC Software - Liteedit116
- Direct Cable Connection116
- Modem Connection117
- Internet Connection118
- IB-Lite119
- Il-Nt-Gprs120
- Internetbridge-NT125
- Ig-Ib125
- Airgate125
- Locate125
- SNMP Protocol125
- Modbus Protocol127
- Communication Object List127
- IL-NT-RD Remote Display Software132
Maintenance137
- Backup Battery Replacement137
Technical Data139
- Inputs/Outputs Overview139
- Generator Protections139
- Language Support139
- Power Supply140
- Operating Conditions140
- Low Temperature Modification140
- Dimensions and Weight141
- Mains and Generator141
- Binary Inputs and Outputs141
- Analog Inputs142
- Speed Pick-Up Input142
- D+ Function142
- CAN Bus Interface142
- IL-NT RS232 Interface (Optional Card)143
- IL-NT RS232-485 Interface (Optional Card)143
- IL-NT S-USB Interface (Optional Card)143
- IL-NT AOUT8 Interface (Optional Card)143
- IC-NT CT-BIO7 Interface (Optional Card)144
- IL-NT BIO8 Interface (Optional Card)144
- Igs-Ptm145
- Igl-Ra15145
- Ig-Ib145

ComAp intelilite nt amf20 User Manual

Table of Contents

Questions and Answers:

ComAp intelilite nt amf20 Specifications

Related product manuals

Brand	ComAp
Model	intelilite nt amf20
Category	Controller
Language	English